Panasonic DMR-E60 - Manual (Page 26)

26
Timer recording (continued)
ªIf “– –” appears under “Name” after entering a
G- CODE number
Name stands for Programme Position/TV Station Name.
Normally, the name of the TV station or the number of the
programme position is displayed under “Name”.
However, if the TV station information was not automatically set
during Auto Setup due to adverse reception conditions, the “– –”
indication appears instead.
In such a case, follow the operation steps below to correct it.
Use [ 3, 4] (10) repeatedly to select the programme
position on which the TV programme to be recorded
will be broadcast.
After you have entered the information of a TV station, it remains
stored in the unit’s memory, and you do not need to enter it again
in the future.
Note
≥The built-in clock employs 24-hour system.
≥The actual time recorded may be longer than the programme
itself when television programmes are recorded using G- CODE .
≥“Invalid Entry” is displayed when you enter the wrong code.
Reenter the code.
≥“PROG FULL” is displayed in the unit’s display if there are already
16 items programmed. Delete unnecessary items (page 27).
≥The remaining time displayed is calculated based on the current
recording mode.
≥When recording more than one programme in a row, for DVD-
RAM the first few seconds, and for DVD-R about the first 30
seconds of all programmes from the second one onwards will not
be recorded.
≥Recording is not possible unless you set “Disc Protection” in
“DISC INFORMATION” to “Off”. (page 30)
≥You can not record to a disc if the write protect tab on a cartridge
disc is set to protect. Release this before operation (page 65).
≥Even if the unit is put in the timer recording standby mode or the
timer recording is being performed, you can play a programme.
Manual programming
[RAM] [DVD-R]
Remote control only
You can set your own programming conditions (up to 16
programmes).
Preparation
≥Switch [DVD, TV] (19) to “DVD”.
≥Ensure that this unit’s clock is set correctly.
≥Insert a disc for recording (make sure there is enough room for
the programme you are going to record plus a little extra).
1 Press [PROG/CHECK] (13).
≥The Timer Programme List screen appears.
A line that is ready for programming is highlighted.
2 Press [ENTER] (10).
≥The Timer Programme Correction screen appears.
3 Use [ 1] (10) to move through the items and change
the items with [ 3, 4] (10).
≥The current settings are shown each time you press [1] (10).
≥You may use the numeric buttons (4) to enter “Name”,
“Date”, “Start” and “Stop”.
≥Name (Programme Position/TV Station Name)
≥Date
Current date >the day before one month later>
Daily (Sunday to Saturday) >Daily (Monday to Saturday)>
Daily (Monday to Friday) >Weekly (Sundays)>…>
Weekly (Saturdays)
≥Start (start time)/Stop (finish time)
The time increases or decreases in 30-minute increments if
you hold the button.
≥Mode (Recording mode)
XP >SP>LP>EP>FR (page 20)
≥Title
Select “Title” and press [ENTER] (10), then refer to page 29
for entering title.
4 Press [ENTER] (10) when you have finished making
changes.
≥To continue programming:
Repeat steps 2, 3 and 4.
5 Press [PROG/CHECK] (13) or [RETURN] (28).
RETURN
SELECT
SP OK 1:22 1:19 64 ABC 15/ 7 TUE 01
Mode Disc
space Stop Start No. Name Date
1:58 SP TIMER
RECORDING Remain
1:19:00 15.7. TUE
ENTER
New Timer Programme
Press ENTER to store
new programme.
RETURN
No. SELECT
1:58 SP
TIMER
RECORDING
Remain
1:55:00 15.7. TUE
ENTER -- 0 9
--:-- --/-- ---
Mode Stop Start Name Date
--:-- SP
Please set Channel.
Title
1:58 SP
TIMER
RECORDING Remain
1:19:00 15.7. TUE
2:00 15/ 7 TUE
Mode Stop Start Name Date
SP 64 ABC 1:00
Title