Panasonic MA Motion Sensor Series - Manual (Page 7)

MA Motion Sensor (AMA1, AMB1, 2, 3)
TIMING CHART
1. Built-in oscillation circuit type
Notes: 1. Circuit stability time : Max. 12 ms
2. During the time taken for the circuit to stabilize after the power is turned on, the ON/OFF status of the output transistor is not determined by whether the sensor is
in the detection status or non-detection status.
2) External triggering type (trigger conditions: trigger pulse width = 20µs and trigger synchronization = 5ms)
Items Symbol
Thin short type
Note 1
Short type Middle type Long type Measured conditions NPN
output
type
PNP
output
type
Rated operating voltage
Minimum
Vdd
5V DC type: 4.5V/Free-ranging type: 6.5V
Typical —
Maximum 5V DC type: 6.5V/Free-ranging type: 27V
Average current
consumption
Without
trigger input
Output OFF
Minimum
Ib
—
Note 2: *b Typical 0.1m 5V DC type: 0.1mA/Free-ranging type: 1.0mA
Maximum 0.3m 5V DC type: 0.3mA/Free-ranging type: 1.8mA
Output ON
Minimum
Id
—
Note 2: *d Typical 2.6mA 6.7mA 5V DC type: 0.5mA/Free-ranging type: 1.4mA
Maximum 6.6mA 9.6mA 5V DC type: 3.4mA/Free-ranging type: 4.5mA
With trigger
input
Output OFF
Minimum
Ia
—
Note 2: *a Typical 2.2mA 5V DC type: 2.2mA/Free-ranging type: 3.1mA
Maximum 6.2mA 5V DC type: 6.2mA/Free-ranging type: 7.2mA
Output ON
Minimum
Ic
—
Note 2: *c Typical 4.2mA 6.2mA 5V DC type: 2.4mA/Free-ranging type: 3.3mA
Maximum 8.2mA 12.5mA 5V DC type: 8.2mA/Free-ranging type: 9.3mA
Measuring cycle (Trigger interval) Minimum Tt 5ms/cycle
External trigger
Pulse width
Minimum
Tw
20µs
Maximum 1/2Tt Half off the distance period
Level
Maximum V TL 0.8V
Minimum V
TH
3V Note 3
Response performance:
time from trigger pulse fall to detection output
Maximum Tr 5ms
Output
characteristics Remain voltage Maximum Vr 1 V DC 1.2 V DC 1 V I = 10 mA
Leakage current Maximum Il 5µA 3µA V = 30 mA
Notes: 1. The thin short type is only available for 5V DC.
2. The ratio between the 4 operating modes (*a to *d) depends on the
external trigger period and detector time, and the current consumption
corresponds with this varying ratio.
3. A high level is established in the open state due to pull-up by the internal
circuit. (Refer to the connector wiring diagram.)
4. The output transistor is open collector.
The output transistor is turned ON by the sensor detection status and
turned OFF by its non-detection status.
Stand by
2 ms
(approx.)
2 ms
(approx.)
2 ms
(approx.)
2 ms
(approx.)
Operation
OFF
(With trigger input) (Without trigger input)
Non-detection status Detection status
(The output is latched
by the previous trigger.) (The output is latched
by the previous trigger.)
(With trigger input) (Without trigger input)
OFF
ON
Internal sensor
operation
Trigger input
Output transistor
*a *b *c *d
Detection status:
output transistor ON
Non-detection status:
output transistor OFF
Sensor
Output
transistor
Output
GND
Sensor
Output
transistor
Output
(NPN output types of the AMA series and all of AMB series)
Detection status:
output transistor ON
Non-detection status:
output transistor OFF
(PNP output types of the AMA series)
ON
OFF
OFF
ON
(NPN output types of the AMA series and all of AMB series)
ON
OFF
ON
OFF
Power supply
Output transistor
(open collector)
Non-detection
status
Detection
status
Non-detection
status
Circuit
stability
time
(PNP output types of the AMA series)
Power supply
Output transistor
(open collector)
Non-detection
status
Detection
status
Non-detection
status
Circuit
stability
time
All Rights Reserved © C OPYRIGHT Panasonic Electric Works Co., Ltd.