Roland VG-99 - Manual (Page 168)

168
Chapter 9 Parameter Guide SYSTEM
Parameters That Can Be
Assigned to Separate Controllers
CTL1-4, FC-300 EXP SW1/EXP SW2,
FC-300 CTL1, 2, 4, 6, 8
FC-300 EXP3/CTL3, EXP4/CTL5, EXP5/CTL7
GK S1, S2
GK VOL, EXP PEDAL, FC-300 EXP1/EXP2
Parameter Explanation
Parameters for which ✔ is indicated can be assigned to the control-
lers shown here.
OFF No function is assigned. ✔ ✔ ✔ ✔
ASSIGNABLE
(PATCH) Functions according to the
Control Assign settings in each
individual patch. ✔ ✔ ✔ ✔
PATCH LEVEL
0–100 Provides control of the patch
level. ✔ ✔
PATCH LEVEL
0–200 ✔ ✔
AB BALANCE Provides control of the balance
of the volume in Channel A
and Channel B. ✔ ✔
FOOT VOLUME
[A&B] Provides simultaneous control
of the foot volume in Channel
A and Channel B. ✔ ✔
FOOT VOLUME
[A] Provides control of the foot
volume in Channel A or Chan-
nel B. ✔ ✔
FOOT VOLUME
[B] ✔ ✔
WAH Provides control of the pedal
wah when the pedal wah is
switched on. ✔ ✔
GUITAR
VOLUME [A&B] Provides simultaneous control
of the COSM guitar volume in
Channel A and Channel B. ✔ ✔
GUITAR
VOLUME [A] Provides control of the COSM
guitar volume in Channel A or
Channel B. ✔ ✔
GUITAR
VOLUME [B] ✔ ✔
GUITAR TONE
[A&B] Provides simultaneous control
of the COSM guitar tone in
Channel A and Channel B. ✔ ✔
GUITAR TONE
[A] Provides control of the COSM
guitar tone in Channel A or
Channel B. ✔ ✔
GUITAR TONE
[B] ✔ ✔
MIXER LEVEL
[A&B] Provides simultaneous control
of the mixer volume level in
Channel A and Channel B. ✔ ✔
MIXER LEVEL
[A] Provides control of the mixer
volume level in Channel A or
Channel B. ✔ ✔
MIXER LEVEL
[B] ✔ ✔
PATCH SEL
DEC/INC When set to INC, patch num-
bers increase when patches are
switched; setting this to DEC
causes the VG-99 to switch to
lower patch numbers when
patches are switched. ✔
PU SEL [A&B] Allows you to switch the pick-
ups in Channel A and Channel
B simultaneously. ✔
PU SEL [A] Allows you to switch the pick-
ups in Channel A or Channel B. ✔
PU SEL [B] ✔
S1:TUNER/
S2:BPM TAP The TUNER screen is switched
with S1. S2 can be used for tap
input of the BPM parameter. ✔
PATCH LEVEL
DEC/INC Provides control of the patch
level. ✔
AB BALANCE
toA/toB Provides control of the volume
balance between Channel A
and Channel B. The level from
Channel A is increased with
S1; the level from Channel B is
increased with S2. ✔
MIDI START/
STOP Transmits Start and Stop for
transmission of MIDI Realtime
messages. ✔ ✔ ✔
MMC PLAY/
STOP Transmits Play and Stop for
transmission of MIDI Machine
Control. ✔ ✔ ✔
FC-300
AMP CTL 1/2 Provides control of the FC-
300’s AMP CONTROL1 and
AMP CONTROL2 jacks. This
allows switching of the chan-
nels for guitar amps connected
to these jacks. ✔
PATCH SELECT
INC Switches to higher patch num-
bers when patches are
switched. ✔ ✔
PATCH SELECT
DEC Switches to lower patch num-
bers when patches are
switched. ✔ ✔
PU SEL
toFRONT [A&B] Switches the Channel A and
Channel B pickups towards the
front. ✔ ✔
PU SEL toREAR
[A&B] Switches the Channel A and
Channel B pickups towards the
rear. ✔ ✔
PU SEL toFRONT
[A] Switches the Channel A pickup
towards the front. ✔ ✔
PU SEL toREAR
[A] Switches the Channel A pickup
towards the rear. ✔ ✔
PU SEL toFRONT
[B] Switches the Channel B pickup
towards the front. ✔ ✔
PU SEL toREAR
[B] Switches the Channel B pickup
towards the rear. ✔ ✔
TUNER ON/OFF Switches the TUNER screen. ✔ ✔
BPM TAP Allow tap input for the BPM
parameter. ✔ ✔
PATCH LEVEL
INC Increases the patch level. ✔ ✔
CTL1-4, FC-300 EXP SW1/EXP SW2,
FC-300 CTL1, 2, 4, 6, 8
FC-300 EXP3/CTL3, EXP4/CTL5, EXP5/CTL7
GK S1, S2
GK VOL, EXP PEDAL, FC-300 EXP1/EXP2
Parameter Explanation
VG-99_e.book 168 ページ ２００７年７月５日 木曜日 午前９時２２分