Omega Vehicle Security CN3271 Series - Manual (Page 13)

10
r 1 r 1 r 1 r 1 r 1 =Input Type and Range Value =Input Type and Range Value =Input Type and Range Value =Input Type and Range Value =Input Type and Range Value
0 = TC J From -100 to 1000 °C
1 = TC K From -100 to 1370 °C
2 = TC T From -200 to 400 °C
3 = TC E From -100 to 800 °C
4 = TC N From -100 to 1400 °C
5 = TC S From -50 to 1760 °C
6 = TC R From -50 to 1760 °C
7 = TC B From 0 to 1820 °C
8 = TC L From -100 to 900 °C
9 = TC U From -200 to 600 °C
10 = TC G From 0 to 2300 °C
11 = TC D From 0 to 2300 °C
12 = TC C From 0 to 2300 °C
13 = TC Plat. II From -100 to 1400 °C
14 = RTD Pt 100 From -200 to 850 °C
15 = Linear From 0 to 60 mV
16 = Linear From 12 to 60 mV
17 = Linear From 0 to 20 mA
18 = Linear From 4 to 20 mA
19 = Linear From 0 to 5 V
20 = Linear From 1 to 5 V
21 = Linear From 0 to 10 V
22 = Linear From 2 to 10 V
23 = TC J From -150 to 1830 °F
24 = TC K From -150 to 2500 °F
25 = TC T From -330 to 750 °F
26 = TC E From -150 to 1470 °F
27 = TC N From -150 to 2550 °F
28 = TC S From -60 to 3200 °F
29 = TC R From -60 to 3200 °F
30 = TC B From 32 to 3300 °F
31 = TC L From -150 to 1650 °F
32 = TC U From -330 to 1110 °F
33 = TC G From 0 to 4170 °F
34 = TC D From 0 to 4170 °F
35 = TC C From 0 to 4170 °F
36 = TC Plat. II From -150 to 2550 °F
37 = RTD Pt100 From -330 to 1560 °F
r2 = Decimal Point Position r2 = Decimal Point Position r2 = Decimal Point Position r2 = Decimal Point Position r2 = Decimal Point Position
(Available only for linear range r1 = 15 to 22)
_ _ _ _ . _ _ _ _ . _ _ _ _ . _ _ _ _ . _ _ _ _ . = No decimal
_ _ _ . _ _ _ _ . _ _ _ _ . _ _ _ _ . _ _ _ _ . _ = One decimal figure
_ _ . _ _ _ _ . _ _ _ _ . _ _ _ _ . _ _ _ _ . _ _ = Two decimal figures
_ . _ _ _ _ . _ _ _ _ . _ _ _ _ . _ _ _ _ . _ _ _ = Three decimal figures
r3 = Initial value of the readout scale r3 = Initial value of the readout scale r3 = Initial value of the readout scale r3 = Initial value of the readout scale r3 = Initial value of the readout scale
(Available only for linear range r1 = 15 to 22)
Range: From -1999 to 9999
r4 = final value of the readout scale r4 = final value of the readout scale r4 = final value of the readout scale r4 = final value of the readout scale r4 = final value of the readout scale
(Available only for linear range r1 = 15 to 22)
Range: From -1999 to 9999
r5 = Offset Adjustment r5 = Offset Adjustment r5 = Offset Adjustment r5 = Offset Adjustment r5 = Offset Adjustment
Range: From -500 to 500
Offset value algebraically added to the measured
value.
r6 = r6 = r6 = r6 = r6 =Time constant of the filter applied to Time constant of the filter applied to Time constant of the filter applied to Time constant of the filter applied to Time constant of the filter applied to
the displayed value
the displayed value the displayed value the displayed value the displayed value
Range: From 0 (filter OFF) to 8 seconds.
(First order filter with selected time constant.)
r7 = Alarm action on input fault. r7 = Alarm action on input fault. r7 = Alarm action on input fault. r7 = Alarm action on input fault. r7 = Alarm action on input fault.
When the instrument detects an input failure
condition, the alarm will operate as in presence of:
uP = as in presence of the full scale value.
doun = as in presence of the initial scale value.
C1 = Type of limit action C1 = Type of limit action C1 = Type of limit action C1 = Type of limit action C1 = Type of limit action
LHL-1-NEUTRO.pmd 19/04/2004, 15.07 10