My satellite receiver/stb code is – Ultratec 43FDX10B User Manual
Page 29
USING THE REMOTE TO CONTROL
SET-TOP-BOX/SATELLITE RECEIVER FUNCTIONS
29
Operating the precoded function for your set-top-box/satellite receiver.
This remote is designed to operate different types of set-top-box/satellite systems. You must first program the remote to match the
remote system of your set-top-box/satellite systems. (refer to page 32)
1.
Turn ON your set-top-box/satellite systems.
2.
Aim the remote control at the front of your set-top-box/satellite systems.
3.
Press and release the SET-TOP-BOX (STB) button to switch to set-top-box/satellite pre-coded mode.
4.
Hold down the STB button on the remote and enter the two digit preset code that matches your set-top-box/satellite receiver as
shown on page 32. The indicator light will flash 3 times if the code was accepted.
5.
Aim the remote at the set-top-box/satellite receiver and press the POWER button. The remote will turn off your set-top-box/satellite
receiver when the correct two digit preset code is entered. When this occurs, the remote control is programmed for your set-top-
box/satellite receiver. If the set-top-box/satellite receiver does not turn off, try a different two digit preset code.
6.
The remote will now control your set-top-box/satellite receiver.
NOTES:
1.
If your set-top-box/satellite receiver cannot be operated
after performing the above procedures, your set-top-
box/satellite receiver code has not been precoded into the
remote.
2.
In the unlikely event that your set-top-box/satellite
receiver cannot be operated after performing the above
procedures, please consult your set-top-box/satellite
receiver operating guide.
3.
The remote control will remember the codes you have
programmed until the batteries are removed from the
remote control. After replacing the batteries repeat the
entire programming procedure as stated above.
4.
The ANT button will act as the TV/STB button when in
STB mode.
ቢ
SET-TOP-BOX (STB) button
This button allows the remote to control your satellite
receiver by setting it to SET-TOP-BOX/SATELLITE mode.
ባ
PRECODED SET-TOP-BOX/SATELLITE RECEIVER
buttons
These buttons transmit the chosen precoded set-top-
box/satellite codes.
ቤ
EXCLUSIVE TV buttons
These buttons are for operating the TV.
POWER
TV
VCR
CBL
DVD
1
2
4
5
6
3
7
8
9
0
LAST CH
SLEEP
HELP
EXIT
MENU
CH
VOL
MUTE
PIP
PIP CH
SWAP
FREEZE
PIP MODE
PIP ACCESS
PROG
TV/VCR
SLOW
SOURCE WIZARD
REC
SELECT
ባ
ባ
ቤ
ባ
ባ
ቤ
ቤ
ባ
ቤ
ባ
ቤ
ቢ
C.C
ASPECT
STB
ANT
STATUS
INFO
VCR PLUS+
SVCS
GUIDE/TV
SCHD
VID 1
VID 2
VID 3
VID 4
VID 5
AV2
AV1
AV3
PIX
CLU-5711TSI
POWER
TV
VCR
CBL
DVD
1
2
4
5
6
3
7
8
9
0
LAST CH
SLEEP
HELP
EXIT
MENU
CH
VOL
MUTE
PIP
PIP CH
SWAP
FREEZE
PIP MODE
PIP ACCESS
PROG
TV/VCR
SLOW
SOURCE WIZARD
REC
SELECT
ባ
ባ
ቤ
ባ
ባ
ቤ
ቤ
ባ
ቤ
ባ
ቤ
ቢ
C.C
ASPECT
STB
ANT
STATUS
INFO
VCR PLUS+
SVCS
GUIDE/TV
SCHD
VID 1
VID 2
VID 3
VID 4
VID 5
TAPE
CD
AMP
MODE
CLU-5713TSI
MY SATELLITE RECEIVER/STB CODE IS:
NOTE:
Refer to instruction manual of the set-top-box/satellite receiver for operation of the buttons exclusively for the set-top-
box/satellite receiver.