My audio/video equipment code is, Av1 (cd) av2 (tape) av3 (amp/rcvr) – Ultratec 43FDX10B User Manual
Page 31
31
USING THE REMOTE
TO CONTROL ADDITIONAL AUDIO/VIDEO EQUIPMENT
Operating the precoded function for your Audio/Video component.
This remote is designed to operate different types of Audio/Video component. You must first program the remote to match the remote
system of your Audio/Video component. (refer to page 32 for pre-codes)
1.
Turn ON your Audio/Video component you wish to control with the Remote.
2.
Aim the remote control at the front of your Audio/Video component.
3.
Press and release the AV1, AV2 or AV3 button to switch to Audio/Video component pre-coded mode.
4.
Hold down the AV1, AV2 or AV3 button on the remote and enter the two digit preset code that matches your Audio/Video component,
as shown on page 32. The indicator light will flash 3 times if the code was accepted.
5.
Aim the remote at the Audio/Video component and press the POWER button. The remote will turn off your Audio/Video component
when the correct two digit preset code is entered. When this occurs, the remote control is programmed for your Audio/Video
component. If the Audio/Video component does not turn off, try a different two digit preset code.
6.
The remote will now control your Audio/Video component.
7.
Repeat steps 1 - 6 if you wish to program the remote to control another Audio/Video component. Be sure to use a different A/V
button on the remote, since only one component can be programmed per button.
NOTES:
1.
Your remote control ÒSOURCE WIZARDÓ buttons are
either labeled as ÒAV1, AV2 and AV3,Ó or ÒCD, TAPE, and
AMP.Ó If your remote control ÒSOURCE WIZARDÓ
buttons are labeled as ÒAV1, AV2, and AV3,Ó please
program your Audio/Video components as follow for best
performance. Use ТAV1У to program your CD brand. Use
ТAV2У to program your TAPE brand, and use ТAV3У to
program your AMPLIFIER/RECEIVER brand.
2.
If your Audio/Video component cannot be operated after
performing the above procedures, your Audio/Video
componentÕs code has not been precoded into the
remote.
3.
In the unlikely event that your Audio/Video component
cannot be operated after performing the above
procedures, please consult your Audio/Video equipment
operating guide.
4.
The remote control will remember the codes you have
programmed until the batteries are removed from the
remote control. After replacing the batteries repeat the
entire programming procedure as stated above.
ቢ
AV1, AV2, AV3 Buttons
These buttons allows the remote to control your Audio/Video
equipment by setting it to Audio/Video mode.
ባ
PRECODED AUDIO/VIDEO Buttons
These buttons transmit the chosen precoded Audio/Video
component codes.
ቤ
EXCLUSIVE TV Buttons
These buttons are for operating the TV.
POWER
TV
VCR
CBL
AV2
AV1
AV3
DVD
1
2
4
5
6
3
7
8
9
0
LAST CH
SLEEP
EXIT
MENU
CH
VOL
MUTE
PIP
PIP CH
SWAP
FREEZE
PIP MODE
PIP ACCESS
PROG
TV/VCR
SLOW
SOURCE WIZARD
REC
CLU-5711TSI
SELECT
ቢ
ባ
ቤ
ቤ
ባ
ቤ
STB
STATUS
INFO
VCR PLUS+
SVCS
GUIDE/TV
SCHD
VID 1
VID 2
VID 3
VID 4
VID 5
POWER
TV
VCR
CBL
TAPE
CD
AMP
DVD
1
2
4
5
6
3
7
8
9
0
LAST CH
SLEEP
EXIT
MENU
CH
VOL
MUTE
PIP
PIP CH
SWAP
FREEZE
PIP MODE
PIP ACCESS
PROG
TV/VCR
SLOW
SOURCE WIZARD
REC
CLU-5713TSI
SELECT
ቢ
ባ
ቤ
ቤ
ባ
ቤ
STB
STATUS
INFO
VCR PLUS+
SVCS
GUIDE/TV
SCHD
VID 1
VID 2
VID 3
VID 4
VID 5
HELP
C.C.
ASPECT
ANT
PIX
HELP
C.C.
ASPECT
ANT
MODE
MY AUDIO/VIDEO EQUIPMENT CODE IS:
NOTE:
Refer to instruction manual of the Audio/Video equipment for operation of the buttons exclusively for the Audio/Video
equipment.
AV1 (CD)
AV2 (TAPE)
AV3 (AMP/RCVR)