Viking BRTGK72SS - Manual (Page 4)

4
ELECTRICAL REQUIREMENTS
AREA REQUIREMENTS
IItt iiss tth he e ccu usstto om me err’’ss rre essp po on nssiib biilliittyy tto o::
•contact a qualified electrical installer.
•assure that the electrical installation is adequate and in conformance with the
National Electrical Code, ANSI/NFPA 70-latest edition or Canadian Electrical
Code C22.1-1998 and C22.2 No. 0-M91 (or latest edition), and all local codes
and ordinances. 120 volt, 60-Hz, 15 amp, fused, electrical supply is required. It
is recommended that a separate circuit serving only this appliance be provided.
This appliance is equipped with a power supply cord having a 3-prong
grounding plug. To minimize possible shock hazard, the cord must be plugged
into a mating 3-prong, grounding-type wall receptacle. Do not use an
extension cord.
IIff cco od de ess p pe errm miitt aa sse ep paarraatte e g grro ou un nd diin ng g w wiirre e tto o b be e
u usse ed d,, iitt iiss rre ecco om mm me en nd de ed d tth haatt aa q qu uaalliiffiie ed d e elle eccttrriicciiaan n
d de ette errm miin ne e tth haatt tth he e g grro ou un nd diin ng g p paatth h iiss aad de eq qu uaatte e..
D Do o N No ott g grro ou un nd d tto o aa g gaass p piip pe e.. C Ch he ecckk w wiitth h aa
q qu uaalliiffiie ed d e elle eccttrriicciiaan n iiff yyo ou u aarre e n no ott ssu urre e tth he e
aap pp plliiaan ncce e iiss p prro op pe errllyy g grro ou un nd de ed d.. D Do o N No ott h haavve e aa
ffu usse e iin n tth he e n ne eu uttrraall o orr g grro ou un nd diin ng g cciirrccu uiitt..
V Ve erriiffyy tth he e ffo ollllo ow wiin ng g::
•Refrigerators can fit into residence and can be moved around corners and through doorways.
•Floors can support refrigerator’s weight plus food weight (approximately 1200 pounds each).
•Rear wall is solid and is able to support a (2) horizontally mounted 2X4s (included) bolted to 2 wall studs. The 2X4
board bolt heads must be flush with 2X4 to prevent obstruction.
•Remove anything attached to rear or side walls that can obstruct refrigerator opening.
•Cutout dimensions are accurate.
•Electrical outlet is in correct location.
•Water line in in correct location.
Anti-Tip Requirements
The anti-tip boards should be
fastened into position prior to
moving the unit into the opening.
Note: The space between the
rear of the refrigerator cabinet
and the condensing unit
assembly housing is 1 1/2” (3.8
cm) deep. Additional mounting
boards may be required if the
refrigerator does not touch the
back wall of the enclosure
T TIIP P O OV VE ER R H HA AZ ZA AR RD D
R Re effrriig ge erraatto orr iiss tto op p h he eaavvyy aan nd d ttiip pss e eaassiillyy w wh he en n n no ott
cco om mp plle ette ellyy iin nssttaalllle ed d..
K Ke ee ep p d do oo orrss ccllo osse ed d u un nttiill rre effrriig ge erraatto orr iiss cco om mp plle ette ellyy
iin nssttaalllle ed d..
U Usse e ttw wo o o orr m mo orre e p pe eo op plle e tto o m mo ovve e aan nd d iin nssttaallll rre effrriig ge erraatto orr..
F Faaiillu urre e tto o d do o sso o ccaan n rre essu ulltt iin n d de eaatth h o orr sse erriio ou uss iin njju urryy
5. Turn on main water supply. Check for leaks. Turn saddle valve handle counterclockwise and run water through
copper tubing and into a bucket. Turn saddle valve clockwise to shut off water to copper tubing.
6. Route copper tubing to refrigerator area or water filter area.
7. Leave an additional length of copper tubing coil to facilitate moving the refrigerator out of enclosure for cleaning or
service.
8. See page11 for water connection instructions.
E ELLE EC CT TR RIIC CA ALL S SH HO OC CK K H HA AZ ZA AR RD D
P Pllu ug g iin ntto o aa g grro ou un nd de ed d 3 3--p prro on ng g o ou uttlle ett..
D DO O N NO OT Trre em mo ovve e g grro ou un nd d p pllu ug g..
D DO O N NO OT T u usse e aan n aad daap ptte err..
D DO O N NO OT T u usse e aan n e exxtte en nssiio on n cco orrd d..
F Faaiillu urre e tto o ffo ollllo ow w tth he esse e iin nssttrru uccttiio on nss cco ou ulld d rre essu ulltt iin n
ffiirre e o orr e elle eccttrriiccaall ssh ho occkk..