Refrigerator installation (con’t) – Viking BRTGK72SS User Manual

Page 6

Advertising
background image

6

S

Se

eccu

urriin

ng

g tth

he

e rre

effrriig

ge

erraatto

orrss

1. Locate and predrill 1/4” (.6 cm) holes in the first

mounting board (supplied). Countersink the bolt
heads into the 2 x 4 board using a 1-1/8” (2.9 cm)
counterbore wood bit 1-1/4” (.6 cm) deep. Locate
and mark 2 wall studs to mount the first 2 x 4 board.
Do not cover the electrical outlet (see “Site
Preparations” on p. 3).

2. Bolt anti-tip mounting board securely to wall studs.
3. Predrill 1/4” (.6 cm) in second mounting board

(supplied). Countersink the bolt heads into the 2x4
board using a 1-1/8” (2.9 cm) counterbore wood bit
1/4” (.6 cm) deep.

4. Attach flush to first 2x4.

If application does not have studs, mount to the wall
using a minimum of four 1/4” (.6 cm) diameter
fasteners (not supplied). If cabinets are deeper than
24”, mounting board must be shimmed. The shim
must be structurally secured to the mounting
board.

NOTE: THE SPACE BETWEEN THE REAR OF THE

REFRIGERATOR CABINET AND THE
CONDENSING UNIT ASSEMBLY HOUSING
IS 3” (7.6 CM) DEEP. ADDITIONAL
MOUNTING BOARDS MAY BE REQUIRED
IF THE UNIT DOES NOT TOUCH THE
BACK WALL OF THE ENCLOSURE.

5. To avoid water line damage, verify water line is secure so refrigerator does not run over the water line when

moved into opening.

6. Repeat steps above for second refrigerator.

B

Be

effo

orre

e m

mo

ovviin

ng

g tth

he

e rre

effrriig

ge

erraatto

orrss iin

n p

pllaacce

e,, cco

on

nffiirrm

m tth

he

e ffiin

niissh

he

ed

d d

diim

me

en

nssiio

on

nss,, e

elle

eccttrriiccaall,, aan

nd

d p

pllu

um

mb

biin

ng

g llo

occaattiio

on

nss,, m

miin

niim

mu

um

m

d

do

oo

orr cclle

eaarraan

ncce

ess,, aan

nd

d d

do

oo

orr p

paan

ne

ell iin

nssttaallllaattiio

on

nss aarre

e aaccccu

urraatte

e ((sse

ee

e p

paag

ge

ess 2

2,, 3

3,, &

& 4

4))..

7. Position refrigerators in front of cutout.
8. Remove the top air grille assemblies from both of the refrigerators. (See illustrations on page 7)

a. Remove the center grille blades by lifting up and pulling forward.
b. Remove the grille/end cap assembly by removing the four (4) screws in each black air duct.
c. Remove the black air ducts by removing the

eight (8) screws on the right hinge model and
the seven (7) screws on the left hinge model.
Save the air ducts for the 72” grille installation.

9. Verify operation by plugging power cord. Power

switch will be shipped in the ON position and
showroom switch will be in the ON position. (If
showroom switch is switched to the “OFF” position,
showroom mode is engaged and power is shut off to
the compressor. This mode is for showroom display
only.)

LEVELING
WHEEL BOLTS

LEVELING
FEET

ACCESS TO
LAG BOLTS

2x4 MOUNTING
BOARD

WALL BOARD
OR PLASTER

WALL STUD

LAG BOLT WITH
EXTENDED SHAFT

1-1/2"

24"

OTE:

EFRIGERATOR IN A 24"

EEP OPENING WILL BE

LUSH AT FRONT SURFACE.

SE 1-1/2" THICK MOUNTING

OARD. IF REFRIGERATOR

TO PROTRUDE BEYOND

4", ADDITIONAL MOUNTING

OARD THICKNESS IS

EQUIRED.

3”

BOARDS

REFRIGERATOR INSTALLATION (con’t)

Advertising