Festool DWC 18 - Manual (Page 16)

16
Bit holder assembly
 Set the switch [1-4] into MAN position.
 Set the bit holder [4-2] completely to the hex-
agonal spindle opening [4-4].
 Attach bit into the holder [4-3].
 Then attach the depth stopper on the gear box
as specifi ed in chapter 9.2.
Bit holder disassembly
 Remove the depth stopper as specifi ed in chap-
ter 9.2.
 Use power to pull out the holder from the spin-
dle opening.
8.2 Bit replacement
You can use the depth stopper [1-5] for the bit
replacement [1-6].
 Attach the depth stopper on the bit (see fi gure
[4 b] ).
 By means of jamming the depth stopper with
the bit and concurrent pulling, it is possible to
pull out the bit.
 Then attach a new bit in the holder.
9 Operation
9.1 Switching on and off
 Pressing only the switch [1-2] does not start
the machine – it is not a machine fault!
 Upon screwing to the required depth, the power
tool switches off!
The machine can be switched on by means of sev-
eral methods:
a)
 Set the forward / reverse switch [1-3] into ma-
chine clockwise operation.
 Set the switch [1-4] into MAN position. In order
to switch on the power tool, apply the switch [1-
2] and concurrently press the bit on the screw.
Use the switch [1-2] to gradually regulate the
speed.
b)
 Set the forward / reverse switch [1-3] into ma-
chine clockwise operation.
 Set the switch [1-4] into AUTO position.
 Press the bit on the screw and the power tool
will switch on.
Switch [1-2] does not need to be pressed. Maxi-
mum speed is set automatically.
c)
 Set the forward / reverse switch [1-3] into ma-
chine anti-clockwise operation.
 In order to start the power tool, press the
switch [1-2]. The switch MAN/AUTO [1-4] is
in any position.
Use the switch [1-2] to gradually regulate the
speed.
 If the forward / reverse switch [1-3] is set to
anti-clockwise operation, the screwdriver can
be started only by pressing the switch [1-2] –
without additional pressure on the bit!
 It is not necessary to remove the depth stopper
in order to unscrew screws!
9.2 Depth stopper
Turning the depth stopper sets the screwing depth
– see fi gure [5]. The setting accuracy is approx ±
0.1 mm.
Anti-clockwise rotation =
screws are insert-
ed deeper
Clockwise rotation = screws are insert-
ed to lower depth
Upon setting the depth, set some screws to test
and adjust the depth.
Depth stopper assembly
 Fit the depth stopper [4-1] on the gear box [4-
5], until it engages in the groove.
Depth stopper disassembly
 Remove the depth stopper from the gear box
by pulling it.
9.3 Hook and clip
Use the clip [6-1] to temporarily attach the screw-
driver on the working clothing – it can be attached
by means of a screw [6-2] to the left or right of
the power tool, and it is suitable for right and left
handed people – see fi gure [6].
The screwdriver is equipped with a hook [7-1],
which is used for occasional machine suspension.
It can be attached to the left or right of the power
tool, by means of a screw [7-2] – see fi gure [7].
9.4 Auto feed attachment
The auto feed attachment enables to work con-
tinuously, without unnecessary delays.
Fitting the auto feed attachment
 At fi rst remove the depth stopper [4-1], bit
holder [4-2] and bit, as specifi ed in chapter 8.
 Set the switch [1-4] into MAN position.
 Push the long bit [8-1] completely to the hex-
agonal spindle opening [4-4].
 Then fi t the auto feed attachment on the gear
box.
 Push the attachment until it engages in the
groove of the gear box.
The attachment can be mounted at 30° steps.