Fein BSS 2.0E - Manual (Page 26)

26 en
For your safety.
Read all safety warnings and all
instructions. Failure to follow the
warnings and instructions may result in electric shock,
fire and/or serious injury.
Save all warnings and instructions for future reference.
Do not use this power tool before you have thor-
oughly read and completely understood this
Instruction Manual and the enclosed “General
Safety Instructions” (document number
3 41 30 054 06 1). The documents mentioned should be
kept for later use and enclosed with the power tool,
should it be passed on or sold.
Please also observe the relevant national industrial safety
regulations.
Intended use of the power tool:
BLS: Hand-guided sheet metal shears for cutting sheet
metal in weather-protected environments without water
supply using the application tools and accessories recom-
mended by FEIN.
BSS: Hand-guided slitting shears for cutting sheet metal
and tight curves in weather-protected environments
without water supply using the application tools and
accessories recommended by FEIN.
This power tool is also suitable for use with AC genera-
tors with sufficient power output that correspond to the
Standard ISO 8528, design type G2. This Standard is par-
ticularly not complied with when the so-called distortion
factor exceeds 10 %. When in doubt, please refer to the
generator instruction/specification guide.
Special safety instructions.
Use auxiliary handle(s), if supplied with the tool. Loss of
control can cause personal injury.
Wear personal protective equipment. Depending on appli-
cation, use face shield, safety goggles or safety glasses.
Where appropriate, wear dust mask, hearing protectors,
gloves and workshop apron capable of stopping small
abrasive or workpiece fragments. The eye protection
must be capable of stopping flying debris generated by
various operations. The dust mask or respirator must be
capable of filtrating particles generated by your opera-
tion. Prolonged exposure to high intensity noise may
cause hearing loss.
Secure the work piece firmly. A work piece that is
gripped tightly in a clamping device or vice, is more
secure than if held by hand.
Do not rivet or screw any name-plates or signs onto the
power tool. If the insulation is damaged, protection
against an electric shock will be ineffective. Adhesive
labels are recommended.
Do not use accessories which are not specifically
designed and recommended by the power tool manufac-
turer. Safe operation is not ensured merely because an
accessory fits your power tool.
Clean the ventilation openings on the power tool at regu-
lar intervals using non-metal tools. The blower of the
motor draws dust into the housing. An excessive accu-
mulation of metallic dust can cause an electrical hazard.
mm mm Max. work-piece thickness for steel with up to
400 N/mm
2
mm mm Max. work-piece thickness for steel with up to
600 N/mm
2
mm mm Max. work-piece thickness for steel with up to
800 N/mm
2
mm mm Max. work-piece thickness for aluminium with up
250 N/mm
2
mm mm Diameter of pilot-drill for inside cut-outs
mm mm Min. inside curve radius
kg kg Weight according to EPTA-Procedure 01/2003
L
pA
dB dB Sound pressure level
L
wA
dB dB Sound power level
L
pCpeak
dB dB Peak sound pressure level
K... Uncertainty
m/s 2 m/s 2 Vibrational emission value according to EN 60745
(vector sum of three directions)
h
m/s 2 m/s 2 Vibrational emission value (nibbler)
m, s, kg, A, mm, V,
W, Hz, N, °C, dB,
min, m/s
2
m, s, kg, A, mm, V,
W, Hz, N, °C, dB,
min, m/s
2
Basic and derived units of measurement from the
international system of units SI.
Character Unit of measurement,
international Unit of measurement,
national Explanation
Fe 400
Fe 600
Fe 800
Al 250
WARNING
OBJ_BUCH-0000000101-001.book Page 26 Monday, May 27, 2013 9:29 AM