VALERA QUICK 24 - Manual (Page 3)

5
• Only connect this unit to alternating current and check that the electricity supply voltage corresponds to that
indicated on the unit.
• Never immerse this unit in water or other liquids.
• Do not put this unit down where it could fall into water or other liquids.
• Do not try to pull any electrical appliance out when it has fallen into water: disconnect the plug from the
power socket immediately.
• Make sure the appliance is completely dry before using it.
• Keep hot areas of the appliance and the rollers away from the face, neck and other parts of the body.
• Let the metal parts cool before touching them.
• After use always switch the unit off and remove the plug from the power supply socket. Do not pull on
the wire to remove the plug from the power supply socket.
• Do not remove the plug from the power supply socket when your hands are wet..
• Always allow the unit to cool before putting it away. Check that the cord has not been damaged from
time to time.
• Prevent the cord from coming into contact with the metal parts while these are still hot.
• Do not use this unit on wigs that have synthetic hair.
• The elements used to pack the unit (plastic bags, cardboard box, etc.) must be kept out of reach of children
as they are a potential danger to them.
• This unit must only be used for the purposes for which it is expressly intended. Any other use is to be
considered improper and therefore dangerous. The manufacturer accepts no responsibility for damage caused
by improper or erroneous use.
• To avoid dangerous overheating, it is advisable to unwind the entire length of the cord.
• Important: Never leave this unit unattended while it is on
INSTRUCTIONS FOR USE:
COMPONENTS
1) Curlers in 3 sizes:
- n° 8 small curlers
- n° 8 medium curlers
- n° 8 large curlers
2) unheated holding edge
3) temperature indicator dot
• Place all the curlers in the unit, sliding them onto the support pins provided. As the curlers come in three
different sizes, check the diameter indicated at the base of the pins so as to ensure you insert them in the
correct position.
• Close the transparent cover. Place the unit on a smooth, flat surface.
• Warning: the unit will heat up when in use.
• Pull the power cable out to its full length, and insert the plug in the power socket (220-240V 50-60Hz)
• To heat the curlers (1) turn the ON/OFF switch (4) to position I. The indicator light will come on to show that
the unit is working.
• Leave the unit to heat up for at least 10 minutes. The transparent cover must be kept closed until the curlers
are ready for use.
• When the curlers are hot, the red dot (3) on the curler itself will change colour. When it turns from red to
white, this means that the curlers have reached the proper temperature and are ready for use.
• Only use the unit on dry hair.
• Take a strand of hair, pull it straight and wrap it around the curler. The curler must be held on the unheated
holding edge (2). The strand must never be wider than the length of the curler. Start from the tips of the hair
when wrapping the strand around the curler.
• Select the size of curler to be used (small, medium, large) according to the length of your hair and the size
of curl you wish to obtain.
• Select the direction in which the strand of hair is wrapped around the curler according to the type of hairstyle
you which to achieve (traditional curls or hairstyle with added volume).
• After wrapping the strand of hair, fix the curler using the metal clips (7) or butterfly clips (8).
• Repeat the above procedure with the other strands, according to the hairstyle you wish to achieve.
• Leave the curlers to cool down completely.
• Remove the clips one at a time, starting from the ones at the bottom, and taking care not to get the hair tangled.
4) ON/OFF switch
5) cord holder
6) metal clip holder
7) metal clips
8) butterfly clips
00060350 int sett2013 13/09/2013 9.00 Pagina 5