Veris Industries HP SERIES Datasheet - Manual

HU
MIDIT
Y
VERIS INDUSTRIES
800.354.8556 +1 503.598.4564 www.veris.com
Pendant and Insertion
Specialty Humidity Sensors
HN HP
FEATURES
● Thin-film capacitive sensor element recovers from 100% saturation
●
Electronics are encapsulated in stainless probe to resist corrosion
● Fully interchangeable element to 1%, 2%, 3%, or 5% accuracy...no calibration
● Pendant and insertion versions for application flexibility
● Polarity insensitive two-wire 4-20mA or 3-wire 0-5/0-10VDC versions...
flexible systems compatibity
● Calibration-free interchangeable NIST traceable HS element
● Replace digital sensor quickly without calibration...maintain accuracy and
eliminate downtime
● HS element is microprocessor profiled with on-board nonvolatile memory
● Multi-point digital calibration to NIST standards
● NIST certification available
● Recovers from 100% saturation...no damage to sensor
DESCRIPTION
HN and HP Series probe type humidity transmitters are easy to install and
exceptionally accurate. Their long-term stability and trouble-free serviceability
make them the best in the industry. The electronics are embedded inside the probe,
protecting them from condensation-related failures. The thin-film capacitive HS
sensor elements are factory calibrated using NIST traceable calibration equipment,
eliminating the need for field calibration. Field replacement of the sensor element is
a snap with the patented removable sensor, lowering costs and reducing downtime.
APPLICATIONS
● HVAC control for improved comfort & energy savings
● Museums, schools, printing shops, and other locations requiring
humidity control
● Facilitating compliance with ASHRAE standards for environmental control
and indoor air quality
SPECIFICATIONS
Input Power:*
Voltage Model 12-30VDC/24VAC, 15mA max.
mA Model Loop powered 12-30VDC only, 30mA max.
Output Power:
Voltage Model 3-wire, observe polarity
mA Model 2-wire, not polarity sensitive (clipped and capped)
Humidity:
HS Element Digitally profiled thin-film capacitive (32 bit mathematics) U.S. Patent 5,844,138†
Accuracy @ 25°C** ±1%, 2%, 3%, or 5% (specify)@10 to 80% RH; Multi-point calibration, NIST traceable
Reset Rate*** 24 hours
Stability ±1%@20°C (68°F) annually, for two years
Hysteresis 1.5% typical
Linearity Included in accuracy spec.
Temperature Coefficient ±0.1% RH/°C above or below 25°C (typical)
Scaling 0-100% RH
Temperature:
Optional Temperature Transmitter Output Digital, 4-20mA (clipped and capped) or 0-5V/0-10V output; accuracy ±0.5°C (±1°F) typical
Operating Environment:
Operating Humidity Range 0 to 100% RH noncondensing
Operating Temperature Range -40° to 50°C (-40° to 122°F)
† The HS sensing element has a 1-year warranty. The element is not a part of the 5-year product warranty.
* One side of transformer secondary is connected to signal common, so an Isolation transformer or dedicated power supply may be required.
** Specified accuracy with 24VDC supplied power with rising humidity. RTD/Thermistors are not compensated for internal heating of product.
*** Reset Rate is the time required to recover to 50% RH after exposure to 90% RH for 24 hours.
Shielded cabling is required for conformance to EMC standards. Technical information is available from factory upon request or is available on our website: www.veris.com.
EMC Conformance - CE Option: Low Voltage Directive 2006/95/EC and EMC Directive 2004/108/EC.
EMC Special Note: Connect this product to a DC distribution network or an AC/DC power adaptor with proper SURGE PROTECTION (EN 61000-6-1:2007 specification requirements).
HN & HP SERIES
HQ0001793.B 01131