Veris Industries H701 Install - Manual

6%2)3 CURRENT MONITORING INSTALLATION GUIDE
Z201482-0D PAGE 1 ©2009 Veris Industries USA 800.354.8556 or +1(0)503.598.4564 / [email protected] 08092
Alta Labs, Enercept, Enspector, Hawkeye, Trustat, Veris, and the Veris ‘V’ logo are trademarks or registered trademarks of Veris Industries, L.L.C. in the USA and/or other countries.
Solid-Core Current Switch,
Adjustable Trip Point
Installer’s Specifications
Sensor Power Induced from monitored conductor
Insulation Class 600VAC RMS (UL), 300VAC RMS (CE)
Frequency Range 50/60 Hz
Temperature Range -15° to 60°C (5° to 140°F)
Humidity Range 10-90% RH, non-condensing
Hysteresis 10% (typical)
Terminal Block Maximum Wire Size 14 AWG (16 AWG for H308)
Terminal Block Torque (nominal) 4 in-lbs (7 in-lbs for H308)
Agency Approvals UL 508 open device listing
CE: EN61010-1:2001-02, CAT III, deg. 2, basic insulation
Do not use the LED status indicators as evidence of applied voltage.
For applications requiring double or reinforced insulation, please contact the factory.
The product design provides for basic insulation only.
)";"3%
0'
&-&$53*$
4)0$,

&91-04*0/

03
"3$
'-"4)
t
'PMMPX
TBGF
FMFDUSJDBM
XPSL
QSBDUJDFT
4FF
/'1"
&
JO
UIF
64"

PS
BQQMJDBCMF
MPDBM
DPEFT
t
5IJT
FRVJQNFOU
NVTU
POMZ
CF
JOTUBMMFE
BOE
TFSWJDFE
CZ
RVBMJmFE
FMFDUSJDBM
QFSTPOOFM
t
3FBE

VOEFSTUBOE
BOE
GPMMPX
UIF
JOTUSVDUJPOT
CFGPSF
JOTUBMMJOH
UIJT
QSPEVDU
t
5VSO
Põ
BMM
QPXFS
TVQQMZJOH
FRVJQNFOU
CFGPSF
XPSLJOH
PO
PS
JOTJEF
UIF
FRVJQNFOU
t
6TF
B
QSPQFSMZ
SBUFE
WPMUBHF
TFOTJOH
EFWJDF
UP
DPOmSN
QPXFS
JT
Põ

%0
/05
%&1&/%
0/
5)*4
130%6$5
'03
70-5"(&
*/%*$"5*0/
t
0OMZ
JOTUBMM
UIJT
QSPEVDU
PO
JOTVMBUFE
DPOEVDUPST
'BJMVSF
UP
GPMMPX
UIFTF
JOTUSVDUJPOT
XJMM
SFTVMU
JO
EFBUI
PS
TFSJPVT
JOKVSZ
%"/(&3
Wiring ExamplE
H701 701
DimEnsions
/05*$&
t
5IJT
QSPEVDU
JT
OPU
JOUFOEFE
GPS
MJGF
PS
TBGFUZ
BQQMJDBUJPOT
t
%P
OPU
JOTUBMM
UIJT
QSPEVDU
JO
IB[BSEPVT
PS
DMBTTJmFE
MPDBUJPOT
t
5IF
JOTUBMMFS
JT
SFTQPOTJCMF
GPS
DPOGPSNBODF
UP
BMM
BQQMJDBCMF
DPEFT
t
.PVOU
UIJT
QSPEVDU
JOTJEF
B
TVJUBCMF
mSF
BOE
FMFDUSJDBM
FODMPTVSF
quick install
Disconnect and lock out power. 1.
Install the mounting bracket to the back of the electrical enclosure, no closer than 2.
1/2” (12mm) to an uninsulated conductor.
Slide the conductor to be monitored through the sensing hole of the current 3.
switch. Terminate the conductor. See Notes (page 2) for currents under 1 Amp or
above 135 Amps.
Wire the output connections to the DDC controller or switched load. Note: 4.
Contacts are solid state and work like dry contacts. When the switch is closed, less
than 1 Ω is present. When the switch is open, more than 1 MΩ are present.
Reconnect power. 5.
Calibrate the sensor (see Calibration section). 6.
Fan or Pump
CONTACTOR
DDC CONTROLLER
Insulated Conductor Only
DI
Motor
701
0.2” x 0.15”
slot (2x)
1.1"
(27 mm)
2.8"
(68 mm)
0.7" Dia
(19 mm)
0.9"
(23 mm)
3.0"
(75 mm)
Removable/Adjustable Mounting Bracket
3.8"
(95 mm)
4.2"
(106 mm)