Velleman DVM1000 - Manual (Page 6)

09
•
•
•
7.
•
•
•
•
•
No
7.
•
•
•
•
•
•
•
•
No
7.
•
•
•
•
•
.03.2010
Never perfo
capacitors i
“Hold” Fun
“Light” Fu
button agai
1 Voltage
Do no
Always
the pro
linked
Connect the
Set the rota
possible ran
Select the A
Connect the
The measur
otes:
• For DC-m
preceded
• When th
higher ra
2 Curren
Do not
Current
measur
betwee
Always
probe b
For measu
"COM" jack
For measu
jack.
Set the rota
possible ran
Set the rota
test probe i
Set the rota
the 10A jac
Select the A
Connect the
Read the m
otes:
• For DC-c
value is
• The mA-
PROTECT
• When m
between
3 Continu
Do not
Connect the
Set the rota
Connect the
Continuity:
When the m
showed on
circuit, the
Diode test:
Connect the
will display
“1”.
orm resistan
n the circuit
nction: Pres
unction: Pre
in to switch
e measur
ot measure
s be careful
obe barriers
to a circuit w
e black test
ary selector
nge and lowe
AC/DC voltag
e test leads
red value ap
measuremen
d by a “-” si
he measured
ange.
t measur
measure cu
t measureme
ring currents
n 2 measure
be careful w
barriers at al
urements u
k.
urements u
ary selector
nge and lowe
ary switch to
is connected
ary switch to
ck).
AC or DC ran
e test probes
measured val
current mea
preceded by
-range is pro
TED!
measuring cu
n 2 measurem
uity & dio
t perform c
e black test
ary selector
e test leads
measured res
the display.
display will
e red test lea
the approxi
ce, diode, tr
t are dischar
ss HOLD to f
ss and hold
the backligh
rements
circuits wh
when workin
at all times
which is bein
lead to the C
at the desire
er to the app
ge range wit
to the circui
ppears on the
nts: when a
gn.
d value is hig
rements
rrent in circu
ents: mA jac
s up to 10A,
ements.
when workin
ll times durin
p to 200mA
p to 10A: c
at the desire
er to the app
o the 200µA/
d to the mA j
o the 10A ra
nge with the
s in series w
ue from the
surements,
y a “-” sign.
otected again
rrents up to
ments.
ode test
ontinuity o
lead to the C
to .
to the circui
sistance is le
Should the
show “1”.
ad to the an
mate forwar
DVM
ransistor or c
rged.
freeze the va
the “LIGHT”
ht off.
here voltag
ng with volta
during mea
ng tested.
COM jack an
ed V rang
propriate ran
th the AC/DC
t under test
e display.
negative po
gher than the
uits with vol
ck max. 200
max. 15s co
g with volta
ng measurem
A: connect t
onnect the r
ed A rang
propriate ran
/2mA/20mA
jack).
ange for mea
e AC/DC butt
with the circu
display.
when a nega
nst over-cur
10A, max.
or diode me
COM jack an
t/componen
ess than 70Ω
measured re
ode; connec
rd voltage dr
1000
6
continuity m
alue onto the
” button to a
es > 600V
ages above 6
asurement. D
nd the red te
e. When the
nge.
C button (AC
.
larity is pres
e selected ra
tages > 250
0mA; for mea
ontinuous m
ges above 6
ment.
he red test l
red test lead
e. When the
nge.
A/200mA ran
asurements
ton (AC = al
uit.
ative polarity
rrent with a
15s continuo
easurement
nd the red te
t under test
Ω a continuo
esistance ex
ct the black
rop. If the le
measurement
e display. Pr
activate the b
CAT III or
60Vdc or 30
Do not touch
est lead to th
e range is un
C = alternati
sent at the r
ange limit, th
0V
asurements
measurement
60Vdc or 30V
ead to the "
to the "10A
e range is un
nge for meas
up to 10A (o
ternating cu
y is present
F200mA 250
ous measure
ts on live ci
est lead to th
t.
ous beep is p
xceed the se
test lead to
ead connectio
ts on live cir
ress again to
backlight. Pr
> 1000V C
Vac rms. Ke
h unused term
he VΩ jack.
nknown, alwa
ing current,
red test lead
he display w
up to 10A u
t followed by
Vac rms. Kee
mA" jack an
A" jack and t
nknown, alwa
surements up
only when te
urrent, DC =
at the red te
0V fuse, the
ement follow
ircuits.
he VΩ jack.
produced and
lected range
the cathode
on is reverse
cuits. Make
o resume nor
ress and hold
CAT II may
eep your fing
minals when
ays select th
DC = direct
, the indicat
will show “1”.
use the 10A j
y a 15 minut
ep your finge
nd the black
the black lea
ays select th
p to 200mA
est probe is
direct curre
est lead, the
10A range i
wed by a 15 m
d the voltage
e or in case o
of the diode
ed, the mete
Rev
©Velleman
sure all
rmal operati
d the “LIGHT
y occur.
gers behind
n the meter
he highest
current)
ted value is
. Select a
jack. When
tes break
ers behind th
lead to the
ad to the "CO
he highest
(only when
connected to
ent).
e indicated
s NOT
minutes brea
e drop is
of an open
e. The meter
er will displa
v. 01
n nv
on.
T”
is
he
OM"
o
ak
r
y