S&B Filters Cold Air Intake Kit - Cotton Filter 75-5066 - Manual (Page 3)

15461 Slover Ave., Fontana, CA 92337 - Phone: (909) 947-0015 - Fax: (909) 947-0603 - www.sbfilters.com
Installation Instructions (continued)
25.
Reconnect the battery. Inspect your
installation, make sure the kit is properly
positioned and all fasteners are secure. Affix
the CARB sticker (if applicable) near the
intake kit. The installation is now complete.
SEE EXPLODED VIEW ON PAGE 4
3
P/N: 75-5066 / 75-5066D
Air Box End Cap Testing
"
Stock air boxes are a significant contributor to
poor air flow which is why S&B designs
custom air boxes with secondary and/or
enlarged openings. With that said, S&B
recognizes the benefits of cooler air, so we
have included a plug to seal off the opening if
so desired. For optimal performance, we
recommend that the intake be used without
the end cap except in conditions of extreme
heat. "
"
Emissions Standard"
The California Air Resource Board (CARB) requires that an E.O. identification label be applied to the vehicle in order to pass a smog check inspection when a Performance
Intake Kit has been installed. You must place the E.O. label provided on or near the intake kit after installation so that a smog check technician can easily verify the E.O. number.
As of April 2009, S&B has never had a product where CARB denied an exemption request; however, the exemption process with CARB can take as long as 18 months. Check
the status of the exemption process by looking up a specific part number at www.sbfilters.com . The CARB Exemption number and/or status is listed under the Product Details
section for each part number. If the status shows as “Pending,” CARB has yet to issue an exemption. Products that have not been issued an EO number are street legal in most
states, but may not be used on emission controlled vehicles in the state of California and are for off road use only. If you purchased your kit from S&B Filters directly, we will
automatically mail you your Exemption Sticker when it is issued to us. If you purchased your kit from an authorized S&B Filters Dealer, log onto our web site and register to
receive your Exemption Sticker.
22.
Secure the Silicone Step Coupler (B) to
the throttle body using a #56 Hose Clamp (A) .
Place the #60 Hose Clamp (C) around the top
of the Silicone coupler.
23.
Insert the Intake tube assembly into the
Silicone Coupler, then slide the Hump Adapter
over the Adapter Tube. Tighten all hose
clamps when you are satisfied with the
positioning.
24.
Reconnect the Temp. Sensor wiring
harness.
21.
Place a #72 Hose clamp (F) over each
end of the Hump Coupler (G) . Then slide the
hump coupler over the end of the Intake
Tube
(E) .
Related Items to Your
Purchase!
• Replacement Air Filter (Oiled)"
(S&B P/N: KF-1056) "
"
• Replacement Air Filter (Dry)"
(S&B P/N: KF-1056D) "
"
• Air Filter Wrap (S&B P/N: WF-1034)"
"
• Air Scoop (2013 Ram 1500)"
(S&B P/N: AS-1006)"
"
• Air Scoop (2009-13 Ram 2500/3500)"
(S&B P/N: AS-1013)
Precision II"
Filter Cleaning & Oiling ""
""
""
""
""
"
Order online today at www.sbfilters.com or
through your local S&B distributor.!
Part #: 88-0008
Warning!"
If your vehicle has a Vehicle Emission Control Information decal affixed to the factory airbox, a new"
replacement label must be obtained and installed in a readily visible position in the engine compartment in "
order to remain CARB compliant. Failure to do so will prevent the vehicle from passing a smog check. "
Replacement labels can be ordered from your local dealership. Regulations state that the VECI label shall "
not be affixed to any equipment which is easily detached from the vehicle. Label placement, under the hood "
on a painted surface is recommended.
Performance Testing"
• Engage parking brake and start your engine.
Listen for abnormal noises. If an air leak is
detected, re-inspect hoses and connections as
they may need to be repositioned and tightened."
• S&B FILTERS recommends that you keep your
OE intake system in the event it is required in
the future."
• Re-tighten all clamps after the first 100 miles of
use. "
• In order to maintain your warranty, all
connections and components must be checked
periodically for alignment and for proper tension
on all connections. Failure to do so may void
your warranty."
• Use only S&B FILTERS cleaning and oil
products to service your filter. Using any other
brand oil and or cleaners on your S&B air filter
may void your warranty.