Factory Direct Hardware Delta 81T201-6-WMSHW - Manual

Electronic Exposed
Teck ® Flush Valves
Delta reserves the right (1) to make changes in specifications and materials, and (2) to change or discontinue models, both without notice or obligation.
Dimensions are for reference only. See current full-line price book or www.specselect.com for finish options and product availability.
DSP–81T201-WMS Rev. B
Refer to www.specselect.com for individual models. Note: Use this page as a product submittal sheet.
124mm
(4 1/2")
124mm
(4 1/2")
* 76mm
(3")
to top
of open
seat cover
Junction Box
51 x 102mm
(2" x 4")
Stainless Steel
Coverplate
Sensor Box
102 x 102 x 51mm
(4" x 4" x 2")
Engineer/Architect Approval
Model Specified:
Approval: Date:
81T201-WMSHW
Note: Measurements may vary ± 6mm (0.25'')
Note: For high and low pressure applications, please see page 7.C.18 High Water Pressure
note for more details.
Verify flow requirements with bowl manufacturer.
Approvals:
• CSA certified
• Complies to ASSE 1037
• ADA Compliant and meets Handicapped
Accessibility Standard ASME A117.1 of
less than 5 lbs. operating force.
• IAPMO listed
(Contact Delta Representative for State
and/or Local Approvals.)
060704A 110 to 24VAC Class II 20VA
(for up to 5 Sensor Modules)
060771A 110 to 24VAC Class II 40VA
(up to 10 Sensor Modules)
060772A 110 to 24VAC Class II 100VA
(up to 25 Sensor Modules)
✔
TRANSFORMERS:
81T201-WMSHW
❏ 81T201-WMSHW
– Exposed Hard Wire Operated
1-1/2'' Top Inlet Closet Fixture
• Polished chrome plated vandal resistant metal cover with 4" wallmount sensor
• Right or left-hand supply installation
• ADA compliant, automatic operation hard wire powered
H
2
O PTICS ™ technology infrared sensor
• Infrared sensor range adjustment of 610mm-1422mm (24" - 56"), in 8" increments,
factory set at 40” (±2")
• Hardwire adaptor
• Vandal resistant copper tube conduit
• 24 hour courtesy flush factory set to off
• 24 VAC input
• Electronic manual override button
• (110 to 24 VAC Transformer not included. See selection below for additional
part number.)
• Quiet action, Teck ® exposed diaphragm flush valve
• Chloramine resistant diaphragm
• Forged brass diaphragm retainer
• Renewable seat
• Polished chrome plated finish
• External water conserving flush adjustment,
factory set at 60 PSI to 6 litre (1.6 US gal.) (except -48 and -6 models)
• 1" FIP/Copper sweat inlet adaptor, angle check stop with protecting cap
• Adjustable 121mm (4-3/4") plus or minus 11mm (7/16") inlet/valve outlet centers
• Vacuum breaker
• Cover tube, stainless steel wall flange, spud flange, concealed spud nut, and 292mm
(11-1/2") outlet tube
❏ 81T201-6-WMSHW
Same as 81T201-WMSHW,
but Not Field Adjustable
❏ 81T201-48-WMSHW
Same as 81T201-WMSHW, but factory set
at 60 PSI to 4.8 litre (1.27 US gal.),
Not Field Adjustable
121mm ±13mm
(4.75" ±.44")
71mm
(2.81")
76mm
(3.0")
VACUUM
BREAKER
TUBE
38mm
(1.5")
38mm (1.5")
SLIP JOINT NUT
& WASHERS
SUPPLIED
124mm
(4.875")
292 mm (11.5”)
54mm
(2.13") MIN.
FINISHED
WALL
TOP OF FIXTURE
INLET:
25mm (1.0")
FIP OR
COPPER
SWEAT
W/ADAPTOR
(SUPPLIED)
* Note:
Recommended
height to sensor
from top of
fixture is
20-22" with
24" MAX.