Factory Direct Hardware Copper Creek HZE2630SF - Manual

OPERATION MANUAL FOR DIGITAL DEADBOLT
EDA-34
FUNCTIONS OPERATING STEPS
1.1 Automatic-Bolt Direction
Determination (Door
Handing)
1.1.1 Insert only three batteries first, and then press and hold ENTER, and then insert the final battery into the interior
receiver module.
1.1.2 Release ENTER when you hear 3 beeps and then the lock automatically determines the “door handing” and sets the
proper direction for motor to rotate.
1.2 To unlock
1.2.1 Enter a valid UC, and the lock will automatically unlock.
1.2.2 Turn turnpiece to vertical position to retract bolt to unlocked position.
1.3 To lock
1.3.1 Press ENTER to lock.
1.3.2 Turn turnpiece to horizontal position to extend the bolt into locked position.
Note ：If the operation fails, the latch bolt will extend twice automatically.
2.1 To add new user code
(up to 6 different UC )
2.1.1 In the unlocked mode, input PC and press ENTER and ○
1 and ENTER. The ENTER will star to flash green.
2.1.2 Enter a new UC and then press ENTER to store the new UC. and then ENTER flashes green followed by a
confirming melody.
2.2 Delete one existing user
code
2.2.1 In the unlocked mode, input PC and press ENTER and ○
2 and ENTER. The ENTER will star to flash green.
2.2.2 Enter the existing UC and press ENTER, and then ENTER flashes green followed by a confirming melody. The user
code is deleted.
2.3 Delete all user codes
2.3.1 In the unlocked mode, input PC and press ENTER and ○ 3 and ENTER, the ENTER will then flash green followed
by a confirming melody. All user codes are now deleted.
Note ：This operation will delete all user codes except programming code.
2.4 Automatic locking set
and cancel
2.4.1 Set auto lock ：In the unlocked mode, input PC and press ENTER and ○
4 and ENTER. Then ENTER will flash
green followed by a confirming melody. (The lock will auto lock after being unlocked for 15 seconds).
2.4.2 Modify automatic locking time: In the unlocked mode, input PC and pressn ENTER and ○
5 and ENTER, then
while ENTER flashes green for ten seconds, input the time (from 10 to 99 seconds) and then press ENTER to store.
Then ENTER flashes green followed by a confirming melody.
2.4.3 Cancel auto lock ：In the unlocked mode, input PC and press ENTER and ○
6 and ENTER, then ENTER flashes
green followed by a confirming melody.
2.5 Set/Cancel Mute Mode
2.5.1 In the unlocked mode, input PC and press ENTER and ○ 7 and ENTER, then ENTER flashes green followed by a
confirming melody.
3.1 Change Programming
Code
3.1.1 In the unlocked mode, input PC and press ENTER and ○
0 and ENTER .Then while ENTER flashes green,
3.1.2 Enter the new PC (up to 4-10 digits in length) and press ENTER to store the new PC within 10 seconds.
ENTER flashes green followed by a confirming melody.
3.2 Recover the preset
programming code
3.2.1 Remove one of the batteries and press any one button 3 times to eliminate the remaining power, then press and
hold the ○ 0 button, insert the batteries, release the ○ 0 button after you hear 3 beeps, the preset PC is now recovered.
4.1 Create a temporary user
code (e.g. guest, neighbor,
etc.)
4.1.1 In the unlocked mode, input PC and press ENTER and ○
1 and ENTER. Then ENTER will start to flash green.
Enter a new UC and then press ENTER to store the new UC. Then ENTER flashes green followed by a confirming
melody.
4.1.2 Provide temporary user his/her code, but keep a record for yourself in order to delete later on.
4.1.3 When this code is no longer needed, delete the temporary user code (refer to Step 2.2.).
Message definitions and notes:
1. Button operation: The button illuminates for 5 seconds and beeps once when pressed.
2. Successful Programming ：ENTER flashes green one time with one melody.
3. Fail Programming ：ENTER flashes red one time with one melody.
4. ENTER will flash red three times and beep three times when you fail to lock properly.
5. Complete all steps of adding the new UC in the programming mode within 10 seconds.
6. Mute mode: All audio will be cancelled but the signals are still active. Mute does not affect audio warning when
the battery is low.
7. In Mute mode, ENTER flashes green indicating the operation is successful ； ENTER flashes red indicating
the operation is unsuccessful.
8. ENTER will flash red and beep for 5 seconds if wrong user code is entered 4 consecutive times or if 20 wrong
digits are entered consecutively, the lock will stop operating for 3 minutes after the beeping stops. (Hint ：
Turning turnpiece or key to unlock will reactivate the lock.)
9. Lock must be in the unlocked mode before programming. If programming attempted while in locked mode,
wait 5 seconds, unlock and re-program.
10. If programming fails (while in the unlocked mode), confirm the turnpiece is vertical and the deadbolt retracts
properly.
11. Low battery warning: Replace with four alkaline batteries when ENTER button flashes red 15 times
accompanied by 15 rapid beeps.
Note ：If ENTER flashes red, this indicates an error or failed operation. Please refer to the above instruction to
confirm the error.
*Important information:
1. The preset UC and PC code are unique and different for each deadbolt.
2. Change the PC and UC as soon as possible after installation to ensure security.(Please refer to the following Functions & Operating
Step 2.1,2.2& 3.1)
3. Every programming operation has to be done while in unlocked mode.
4. If wrong UC entered, then press ENTER button first to clear the wrong code, and then input the correct UC.
Note ：UC and PC can be up to 4-10 random digits in length.
5. One unique PC and 2 random UC are printed on two stickers, one on this manual, the other on the interior
face of exterior keypad. Please keep this operation manual in a safe place for security purposes.
STICKER
Programming Code:xxxx
User Code A:xxxx
User Code B:xxxx
xxxx.xx.xx