Factory Direct Hardware Toto TEU1LN12#CP - Manual

Variation & Specification
INSTALLATION MANUAL
Set-up Drawing
Model number
Figure
Approx. 1.6
gallon (6L)
Approx. 3.5
gallon (13L)
c
Connection of the
water supply pipe
Supply water
pressure
Shutoff pressure
Discharge quantity
per flush at 28 PSI
(196kPa)
(Factory set)
7 PSI (48kPa)
1"NPT
Model number
Detection time
Urinal Flush Valve
6 seconds or more
Detection time 6 seconds or more
Approx. 1.0 gallon
(3.8L)
Ambient temperature
Connection of the
water supply pipe
Supply water
pressure
Shutoff pressure
Discharge quantity
per flush at 28 PSI
(196kPa)
(Factory set)
Minimum required water pressure: 15 PSI (103kPa)
(flowing)
Maximum water pressure: 125 PSI (862kPa)
7 PSI (48kPa)
32-104˚F (0-40˚C)
Water temperature 34-104˚F (1-40˚C)
3/4"NPT
Check local codes
TET1GN32#CP
Installation Precautions
Toilet Flush Valve
1. Prior to Installation
Prior to Installing your TOTO ®` s EcoPower ® Flush Valve, install the items
listed bellow:
· Closet fixture/Urinal fixture
· Drain line
· Water supply line
The supply piping to these devices shall be securely anchored to the
building structure to prevent the installed device from having unnecessary
movement when operated by the user. Care shall be exercised when
installing the device to prevent marring the exposed surface.
2. Important
All plumbing is to be installed in accordance with applicable codes
and regulations. Water supply lines must be sized to provide an
adequate volume of water for each fixture.
Flush all waterlines prior to operation.
The minimum pressure required to the valve is determined by the type
of fixture selected. Consult fixture manufacturer for pressure requirement.
Do not use toothed tools to install or service the valve.
Be sure to install TOTO ®` s EcoPower ® Flush Valve so that the control stop
is situated no more than 11-1/2"(292mm) above the top of the bowl or
the urinal. Refer to local codes for special requirements.Except for
TET6GN#CP,TEW6GN#CP and TET6LN#CP, make sure that the control
stop is installed 27" adove the top of the bowl for proper valve function.
3. Use care not to damage the surface of the infrared sensor.
4. For Toilet Flush Valve
The toilet sensor valve may not function if toilet seat and/or lid cover are
left upright as it may block the sensor.
5. For Urinal Flush Valve
The Urinal Flush Valve is designed to be used with a washout urinal
for optimum performance. However, a siphon jet urinal may also be
substituted. Blowout urinals are not recommended.
6. The detection range of the infrared sensor is shown in the figure above.
Do not install a handrail or any other object within the detection zone
of the sensor, as any object blocking the sensor may cause the valve to
malfunction. Additionally, to avoid the possibility of valve malfunction, do not
install the flush valve in a location where the sensor faces a mirror,
stainless steel wall, other highly reflective surface or another infrared sensor.
To be continued on the back
Figure
Note
Components
1. Required tools
Adjustable wrench, Phillips and slotted screwdrivers.
2. Inspection
Unpack the flush valve and carefully make sure the cover, main unit and
all other parts are included and intact before starting installation of the
product.
Item Figure Description Q’ty
A
Valve Body
assembly
1
B
Top cover
assembly
1
C
D
Screw 2
F
Back-up
battery Pack
1
G
Tool
(Allen wrench) 1
H
Notice Label 1
Owner's
Manual 1
1
Toilet Flush Valve
For TET1GN32#CP, TEW1GN32#CP, TET6GN32#CP,
I
Vacuum
breaker tube
(with spud
joint)
1
J Control stop 1
K
Sweat
solder kit
(Escutcheon,
covering tube,
adapter)
1
E
TOTO
For the best results, be sure to read the following installation instructions and use the product only as described in this manual.
Ambient temperature
32-104˚F (0-40˚C)
Water temperature 34-104˚F (1-40˚C)
Dimension of Cover
7-3/4" (H) 4-1/2"(W) 3-1/8"(D)
(198mm(H) 115mm(W) 80mm(D))
Dimension of Cover
7-3/4" (H) 4-1/2"(W) 3-1/8"(D)
(198mm(H) 115mm(W) 80mm(D))
Installation
Manual
(this manual)
03585T3R
11-1/2"
(292mm) 1-1/2"
NPSM
Min.2-1/4"(57mm)
3/4"NPT
inlet supply
EcoPower ® Flush Valve
4-3/4" 1/2"
(120 13mm)
4-3/4" 1/2" (120 13mm) Min.2-1/4" (57mm)
1"NPT
inlet supply
11-1/2" (292mm)
Check local codes
1-1/2" NPSM
4-3/4" 1/2"
(120 13mm)
Min.2-1/4"
(57mm) 1"NPT
inlet supply
27" (686mm)
Check local codes
1-1/2"
NPSM
Detection zone
The detection zone is self-adjusting and is equipped with a
3-second flush delay. (No flush delay for Urinal flush valve)
The detection zone may differ according to the color of the
user’s clothes.
When a user wears black clothes, the detection zone may
become smaller and the valve may not flush.
“AVOID”
DO NOT place the Infrared
stainless steel wall, or other
highly reflective surface.
Mirror, Stainless steel wall or
other highly reflective surface.
Infrared sensor of the
another automatic
flush valve.
Infrared sensor of the
automatic flush valve.
“AVOID”
DO NOT place the Infrared
sensor of one urinal so that sensor in front of a mirror,
it is in line with the sensor
of another automatic flush
valve sensor.
Infrared sensor of the
automatic flush valve.
L
Max19-11/16"
(Max 500 mm)
Max31-1/2" (Max 800 mm)
15
L
Max21-1/4"
(Max 550 mm)
Max33-1/2" (Max 850 mm)
20
TET1LN(32)#CP
TET6LN(32)#CP
TEU1GN(12,22)#CP
TET1GN(32)#CP
TET6GN(32)#CP
TEU1LN(12,22)#CP
TEW1GN(32)#CP
TEW6GN(32)#CP
Approx. 1.28
gallon (4.8L)
Approx. 0.5 gallon
(1.9L)
Minimum
(Flowing)
Maximum
15 PSI (103kPa)
125 PSI (862kPa)
35 PSI (241kPa)
TET6GN(32)#CP
TEW6GN(32)#CP TET1LN(32)#CP
TEU1LN(12,22)#CP
TET1GN(32)#CP
TEU1GN(12,22)#CP
TEW1GN(32)#CP
TEW1LN(32)#CP
TEW1GN32#CP
TET1LN32#CP
TET6GN32#CP
TEW6GN32#CP
TET6LN32#CP
TEU1GN(12,22)#CP
TEU1LN(12,22)#CP
TEW6GN32#CP, TEU1GN(12, 22)#CP, TET1LN32#CP,
TET6LN32#CP AND TEU1LN(12, 22) #CP