Xylem IM201 CentriBoost Fixed Speed Pumping Package User Manual

Page 3

Advertising
background image



SectIOn 1

SAFETY INSTRUCTIONS

TO AVOID SERIOUS OR FATAL PERSONAL INJURY

OR MAJOR PROPERTY DAMAGE, READ AND

FOLLOW ALL SAFETY INSTRUCTIONS IN MANUAL

AND ON PUMP.
THIS MANUAL IS INTENDED TO ASSIST IN THE

INSTALLATION AND OPERATION OF THIS UNIT

AND MUST BE KEPT WITH THE PUMP.

This is a SAFetY ALeRt SYMBOL.

When you see this symbol on the pump

or in the manual, look for one of the fol-

lowing signal words and be alert to the

potential for personal injury or property

damage.
Warns of hazards that WILL cause

serious personal injury, death or major

property damage.
Warns of hazards that cAn cause

serious personal injury, death or major

property damage.
Warns of hazards that cAn cause per-

sonal injury or property damage.

nOtIce: InDIcAteS SPecIAL InStRUctIOnS

WHIcH ARe VeRY IMPORtAnt AnD

MUSt Be FOLLOWeD.

tHOROUGHLY ReVIeW ALL InStRUctIOnS

AnD WARnInGS PRIOR tO PeRFORMInG AnY

WORK On tHIS PUMP.
MAIntAIn ALL SAFetY DecALS.

GENERAl dESCRIpTION

The CentriBoost pumping package is a fixed constant

speed, and will increase the domestic water pressure

at the fixtures from 0 to 55 PSI above that of the city

water pressure.
Depending upon the pumping capacity required, a Sim-

plex (one pump) type or a Duplex (two pump) type is

used. In both types, a pressure switch starts and stops the

pump(s).

pURpOSE OF mANUAl

This manual is furnished to acquaint you with some of

the practical ways to install, operate and maintain this

unit. Read it completely before doing any work on your

unit and keep it handy for future reference.
Equipment cannot operate well without proper care. To

keep this unit at top efficiency, follow the recommended

installation and servicing procedure outlined in this

manual.

AddITIONAl SAFETY REQUIREmENTS

ELECTRICAL SHOCK HAZARD.

INSPECT ALL ELECTRICAL CONNEC-

TIONS PRIOR TO POWERING THE UNIT. WIRING

CONNECTIONS MUST BE MADE BY A QUALIFIED

ELECTRICIAN IN ACCORDANCE WITH ALL APPLI-

CABLE CODES, ORDINANCES AND GOOD PRAC-

dANGER

WARNING

CAUTION

TICES. FAILURe tO FOLLOW tHeSe InStRUc-

tIOnS cOULD ReSULt In SeRIOUS PeRSOnAL

InJURY, DeAtH, AnD/OR PROPeRtY DAMAGe.

PREVENT ELECTRICAL SHOCKS.

DISCONNECT THE POWER SUPPLY

BEFORE BEGINNING INSTALLATION. FAILURe tO

FOLLOW tHeSe InStRUctIOnS cOULD ReSULt

In SeRIOUS PeRSOnAL InJURY, DeAtH AnD/OR

PROPeRtY DAMAGe.
Always use accurate test meters when checking electrical

components. Always work with another person in case of

emergency.

STORAGE

For long periods of storage, the unit should be covered to

prevent corrosion and contamination from dirt. It should

be STORED in a clean, dry location between 0 and 170°

F. The relative humidity should not exceed 85%. The

unit should be checked periodically to ensure that no

condensation has formed. After storage, again check that

it is dry before applying power.

HANdlING

Care should be taken to prevent damage due to dropping

or jolting when moving the CentriBoost. Transportation

damage should be brought to the carrier's attention im-

mediately upon receipt.

TEmpERATURE ANd VENTIlATION

All electrical equipment is susceptible to failure if oper-

ated in ambient temperatures outside of its rating. The

OPERATING temperature range for this unit is  to

105° F. The relative humidity should not exceed 95%

non-condensing. The unit should not be operated outside

these extremes.

ElECTRICAl CONNECTIONS - A.C. pOWER
ANd SIGNAlS INpUT VOlTAGE

The input voltage tolerance is +10/-10% of nameplate

voltage.

GROUNd CONNECTIONS

A grounding terminal is provided for a dedicated ground

wire connection. All provisions of the National Electrical

Code and local codes must be followed.

CONDUIT GROUNDS ARE NOT AD-

EQUATE. A SEPARATE GROUND WIRE

MUST BE ATTACHED TO THE GROUND LUG PRO-

VIDED IN THE ENCLOSURE TO AVOID POTENTIAL

SAFETY HAZARDS. FAILURe tO FOLLOW tHeSe

InStRUctIOnS cOULD ReSULt In SeRIOUS

PeRSOnAL InJURY, DeAtH AnD/OR PROPeRtY

DAMAGe.

pOWER WIRING

Power wire types and sizes must be selected based upon

conformance with the National Electrical Code and all

local codes and restrictions. In addition, only copper

WARNING

WARNING

WARNING

Advertising