Extron Electronics FOXBOX Tx_Rx DVI Plus User Guide - Manual (Page 30)

Command/response table for SIS commands (continued)
NOTE: X( = Pixel phase 00 to 31
X1) = Total pixels ± 255 of default value for selected resolution
X1! = Sync frequency xxx.xx (frequency in kHz [H] or Hz [V]
X1@ = Memory preset number 01 to 30
X1# = Audio gain adjustment range 00 to 10
X1$ = Audio level adjustment range -18 to +10 (in 1.0 dB steps)
X1% = Audio attenuation adjustment range 00 to 18
X1^ = Audio output level 0 = consumer (–10 dBV) 1 = professional (+4 dBu)
Command ASCII Command
(host to unit)
Response
(unit to host)
Additional description
Pixel phase
NOTE: When the controlling PC is connected to the receiver, the FOXBOX can perform this command only if the receiver-Tx-to-
transmitter-Rx fiber cable is connected. The unit returns the E14 error if the Rx fiber is not connected.
Set a pixel phase value X( U Phs X(] Set the pixel phase value to X( .
Example: 10U Phs10 ] Set the pixel phase value to 10.
Increment pixel phase +U Phs X(] Increase pixel phase value by 1.
Decrement pixel phase –U Phs X(] Decrease pixel phase value by 1.
Show pixel phase U X(]
Total pixels
NOTE: When the controlling PC is connected to the receiver, the FOXBOX can perform this command only if the receiver-Tx-to-
transmitter-Rx fiber cable is connected. The unit returns the E14 error if the Rx fiber is not connected.
Set a total pixel value 11* X1) # Tpx X1)] Set the total pixels to a specific value.
Example: 11*1555# Tpx1555 ] Set the total pixel value to 1555.
Increment total pixel value +11# Tpx X1)] Increase total pixels by 1 pixel.
Decrement total pixel
value –11# Tpx X1)] Decrease total pixels by 1 pixel.
Show total pixel value 11# Tpx X1)]
List sync frequency
View input frequency 1LS X1! horozontal , X1! vertical ] List the input frequency.
Memory presets
Save preset X1@ , Spr X1@] Command code is a comma.
Recall preset X1@ . Rpr X1@] Command code is a period.
Audio input gain and attenuation
NOTES: • The set gain (G) and set attenuation (g) commands are case sensitive. The increment level, decrement level, and show level are
not case sensitive.
• When the controlling PC is connected to the receiver, the FOXBOX can perform this command only if the receiver-Tx-to-
transmitter-Rx fiber cable is connected. The unit returns the E14 error if the Rx fiber is not connected.
Set input audio gain to a
+dB value X1# G Aud X1$] Set the input level (gain) to + X1# dB.
Example: 2G Aud+02 ] Set the input level (gain) to +2 dB.
Set input audio
attenuation to a -dB value X1% g Aud X1$] Set the input level (attenuation) to – X1# dB.
Increment input level +G Aud X1$] Increase the audio level by 1 dB.
Example: +G Aud+03 ] Increment the input level from +2 dB to +3 dB.
Decrement input level –G Aud–01 ] Decrease the audio level from 0 dB to –1 dB.
Show input level G X1$]
Audio output level
NOTE: The FOXBOX receiver outputs audio at the consumer level (-10 dBV) only. The FOX 500 or PowerCage FOX can be configured to
output audio at the professional level; refer to the applicable User Guide.
Set the output to the
consumer level 40*0# Lvl0 ] Set the audio output to the consumer level
(–10 dBV).
Set the output to the
professional level 40*1 Lvl1 ] Set the audio output to the professional level
(+4 dBu).
Show output level 40# X1^] Show the audio output level.
FOXBOX Tx/Rx • Remote Control 24