NXG Technology NX-PRO6820CE - Manual (Page 4)

New Construction
1. Determine speaker locations and mark them on
your plans for future reference.
2. If possible, run speaker wires after HVAC and
electrical wiring is in place.
3. Secure speaker wires in place along the run
with insulated staples only and be careful not to
pierce the wire’s insulation. Allow a bit of slack for
expansion of building materials.
4. Needless to say, the actual speakers should not
be installed until the wall board is in place. In the
meantime, leave several feet of wire coiled up and
secured at the back side of the mounting hole.
5. To complete installation follow steps 2 through
8 above.
FIG. 7
Operational Check
After making all connections, it’s a good idea to
make sure everything is working properly. Turn
on your surround or stereo system, making sure
the volume control is turned down and that the
balance control is in the center position. Activate
a musical or movie source such as FM, a CD or
DVD player. Gently turn up the volume, you
should hear sound coming from your new NXG
speakers. If no sound is heard from any or all
speakers, switch off the system immediately and
check for open or loose connections, wrong
polarity or shorts, proper transformer tap selector
switch setting, or proper source selection.
NX-PRO6820CE Specifications
Maximum Power Handling: 5 - 120 watts
[40 watts (transformer limited) in 70 volt mode]
Sensitivity: 90dB @ 1 watt/1 meter
Frequency Response: 40 Hz-22,000 Hz
Driver Complement:
6.5˝ (165mm) metallic anodized injection-molded radiative cone woofer
w/rubber surround
1˝ (25mm) metallic anodized liquid-cooled dome tweeter w/minimun diffraction
tilt-swivel island
Transformer Tap Settings: 2W, 5W, 10W, 20W, and 40W (for 70 volt systems)
Plus standard 8 ohm setting (for conventional audio systems)
Nominal Impedance: 8 ohms
Grille: Corrosion-resistant powder coated aluminum
Overall Dimensions: 11˝ (diameter) round x 7˝ D
Required Ceiling Cutout: 9
3 /
4
˝ (diameter) round
NXG Speakers Three-Year Limited Warranty
If the NXG speaker system proves to be defective in workmanship or materials with-
in three years from the date of the original customer’s purchase, we will, at our option,
repair or replace the defective product.
Limitation of Implied Warranties
Any implied warranties, including warranties of merchantability and fitness for a
particular purpose, are limited in duration to the length of this warranty.
Exclusion of Certain Damages
NXG’s liability for any defective product is limited to repair or replacement of the
product at our option. NXG shall not be liable for incidental or consequential dam-
ages of any kind or character because of product defects. Some states do not allow
limitations on how long an implied warranty lasts and/or do not allow the exclusion
or limitation of incidental or consequential damages, so the above limitations and
exclusions may not apply.
This Warranty Does Not Cover:
• Damage caused by abuse, accident, misuse, negligence, or improper operation.
• Any product whose serial number has been altered, defaced, or removed.
• Products that have been altered or modified.
• Normal wear and maintenance.
• Damages caused by shipping. (All claims for shipping damage must be made with
the carrier.)
Warranty Service
Warranty service must be performed by an authorized service center, usually an NXG
speaker systems dealer or its authorized agent. You may obtain a list of authorized
service centers by contacting NXG. All warranty repairs must be accompanied by the
original bill of sales. No other document is acceptable or is required. This warranty
gives you specific legal rights, and you may also have other rights which vary from
state to state.
NXG reserves the right to revise speaker system specifications without notice .
16648 North 94th Street • Scottsdale, AZ 85260
1-800-733-0008 www.nxgtech.com
Input
Connectors
Security
Loop