Document Outline

• 053691b1e__CXPS48-body.pdf
  • 1 Introduction
    • 1.1 Manual scope
    • 1.2 Product overview
    • 1.3 Available system configurations
    • 1.4 Part numbers including options
  • 2 Features
    • 2.1 System overview
    • 2.2 Distribution center
      • 2.2.1 Distribution configurations
      • 2.2.2 Low voltage battery disconnect (LVBD)
      • 2.2.3 Shunt
      • 2.2.4 Internal alarm card
      • 2.2.5 Controller I/O terminal block
      • 2.2.6 8R/8D 8DIO (Option)
    • 2.3 CXCM1 Controller
      • 2.3.1 Controller front panel
      • 2.3.2 LCD screen
      • 2.3.3 LED lights
        • Alarm conditions
        • Progress and status indication
      • 2.3.4 Reset button
      • 2.3.5 Modem port
      • 2.3.6 Ethernet port
      • 2.3.7 Analog input channels
        • Voltage inputs
        • Current inputs
        • Temperature inputs
      • 2.3.8 Digital input channels
      • 2.3.9 Alarm and control output relays
      • 2.3.10 Network connection and remote communications
    • 2.4 Rectifiers
    • 2.5 Rectifier front panel
      • 2.5.1 LEDs
        • AC
        • DC
        • Alarm
        • Locate Module command
        • Firmware upload
      • 2.5.2 Mechanical connections
      • 2.5.3 Rear panel
      • 2.5.4 True module fail alarm
      • 2.5.5 Heat dissipation
      • 2.5.6 Over-temperature protection
      • 2.5.7 Wide AC input power range
      • 2.5.8 AC inrush/transient suppression
      • 2.5.9 Soft start
      • 2.5.10 Start delay
      • 2.5.11 Current-limit/short circuit protection
      • 2.5.12 Power limiting
      • 2.5.13 High voltage shutdown (HVSD)
      • 2.5.14 Battery eliminator operation
  • 3 Inspection
    • 3.1 Packing materials
      • 3.1.1 Returns for service
    • 3.2 Check for damage
    • 3.3 General receipt of shipment
      • 3.3.1 Racks
      • 3.3.2 Rectifiers (purchased separately)
      • 3.3.3 Miscellaneous small parts
      • 3.3.4 Batteries (purchased separately)
  • 4 Installation
    • 4.1 Safety precautions
    • 4.2 Tools required
    • 4.3 Power system assembly and mounting
      • 4.3.1 Rack mounted systems
      • 4.3.2 Floor mounted systems
    • 4.4 Rectifier module insertion/removal
    • 4.5 Breaker installation
    • 4.6 Breaker removal
    • 4.7 Battery installation
      • 4.7.1 Preparation/mounting
      • 4.7.2 Installation of batteries
  • 5 Wiring
    • 5.1 Grounding
      • 5.1.1 Frame ground
    • 5.2 AC feeder protection/sizing
    • 5.3 AC input connections
    • 5.4 Calculating output wire size requirements
    • 5.5 DC output connections
    • 5.6 System and battery connections
      • 5.6.1 DC input to panel
      • 5.6.2 Distribution cabling
      • 5.6.3 Breaker output (hot) connections
      • 5.6.4 Breaker return (ground) connections
      • 5.6.5 Battery breaker connections
    • 5.7 Alarm connections
    • 5.8 CAN serial ports
      • 5.8.1 CAN termination
    • 5.9 Network connection and remote communications via controller
      • 5.9.1 Ethernet port for network connection (standard network cable)
      • 5.9.2 Ethernet port for local connection (crossover cable)
      • 5.9.3 Controller modem port (Alpha cable)
    • 5.10 Signal wiring connections for controller
      • 5.10.1 Alarm (relay) outputs
      • 5.10.2 Digital inputs for controller
        • Connection method
        • Programming the digital input
      • 5.10.3 Analog inputs
        • Voltage
        • Temperature sensor
        • Current
  • 6 System startup
    • 6.1 Check system connections
    • 6.2 Verify AC input and power up rectifier shelf
    • 6.3 Check battery polarity and connect the batteries
      • 6.3.1 Controller alarm Configuration for nominal 120 Vac operation
    • 6.4 Controller Reset
      • 6.4.1 Soft reset
      • 6.4.2 Controller IP address reset
      • 6.4.3 Controller hard reset
      • 6.4.4 Time setting
    • 6.5 LVD control
  • 7 Operation
    • 7.1 Main rectifier states
      • 7.1.1 Off state
      • 7.1.2 Start Delay state
      • 7.1.3 Soft Start state
      • 7.1.4 Normal Operation state
      • 7.1.5 Turning Off state
    • 7.2 Main rectifier modes
      • 7.2.1 Output voltage modes
      • 7.2.2 Output current/power modes
    • 7.3 Factory ranges and defaults
  • 8 Maintenance
    • 8.1 General maintenance schedule
    • 8.2 Fan replacement
  • 9 Warranty
    • 9.1 Warranty
  • 10 Alpha Conventions
    • 10.1 Acronyms
• 05369108A__.pdf
  • Sheet1 (Assembly)
    • Drawing View7
    • Drawing View8
    • Drawing View9
  • Sheet2
    • Drawing View10
    • Drawing View11
• 05369106A__.pdf
  • Sheet1 (Assembly)
    • Drawing View5
    • Drawing View6
    • Drawing View7
    • Detail View A (1 : 2)
  • 19" RACK
    • Drawing View14
    • Drawing View15
    • Drawing View16
    • Drawing View17
    • Detail View B (1 : 6)
  • 23" RACK
    • Drawing View8
    • Drawing View11
    • Drawing View12
    • Drawing View13