intimus Degausser 9000 - Manual (Page 5)

5
9000
GB Translation of the Original Operation Manual
Übersetzung der Originalbetriebsanleitung
MAGNETIC FIELDS
MAGNETIC FIELDS MEASURED AROUND PERIMETER
The intimus 9000 produces a single focused magnetic pulse lasting less than 1/20 of a second. The
focused intensity allows the unit to erase today’s highest coercivity media while also limiting the ma-
gnetic field exposure to 1 second for every 20 pieces of media degaussed.
Distance from side of degausser Magnetic field Duration of Field
0 cm (0”) 61 gauss < 0.05 Second
15 cm (6”) 6 gauss < 0.05 Second
30 cm (12”) 2 gauss < 0.05 Second
Note: The testing room measured 0.4 gauss before degausser was plugged in.
Average Operational Distance (AOD) from user to the degausser is 12-18 inches (30-45cm). According
to the American Conference of Governmental Industrial Hygienists (ACGIH) Threshold Limit Values
(2005) - Static Magnetic Fields, whole body exposure limits recommended for an 8 hour shift are
600 gauss. Because of the short duration of each pulse from an degausser (1/20 th * of a second) and
the extremely small magnetic field outside of the unit (<6 gauss, AOD) the total 8 hour whole body
exposure is 0,004% of the recommended limit.
* Pulse duration was rounded to ½ second per discharge for calculations to cover any build up of magnetic fields
generated before or after discharge.
IMPORTANT SAFETY NOTES
<< The machine may not be operated by more
than one person at any given time!
The machine was designed for safe operation
by “one person only”.
<< During the degaussing process no other
work may be performed on the machine
(for example cleaning, etc.)!
<< The unti is not a toy, and is not suitable
for use by children!
The overall technical safety concept of this
machine does not provide for any guarantee
regarding hazard-free operation by children.
<< Persons with pacemakers must not work
at the unit before having consulted their at-
tending doctor or physiotherapist! Danger
of heart rhythm disturbances due to stray
magnetic fields!
<< In case of danger switch the machine off
with the mains switch, or with the emer-
gency switch, or unplug the unit!
<< Always unplug the machine from the mains
power supply before opening the machine!
Repairs may only be performed by trained
personnel!
INITIATION
INTRODUCTION
The degausser Model intimus 9000 is a conti-
nuous duty capacitive discharge degausser. The
unit is designed to erase hard drives and tape
cartridges that fit within the opening of the Media
Entrance Door. The convenient media loading
design accommodates many different types and
sizes of media, without the need for adapters.
Each erase cycle is measured and verified by
internal diagnostics thus eliminating the possibil-
ity of a non-erasure. For security purposes, if an
insufficient field is detected, the intimus 9000 will
not release the media.
INSPECTION
Inspect the degausser for shipping damage as
soon as it is unpacked. If the degausser or any
accessories are damaged or fail to operate cor-
rectly, notify carrier and contact your dealer im-
mediately.
INSTALLATION
Power Plug
Plug the IEC connector attached to the power
cord supplied into the receptacle on the back of
the unit.
Fuse Block
Always unplug the unit from the mains
power supply before opening the
machine! Changes in power supply
may only be performed by trained
personnel!
Located behind the removable panel on the back
side of the unit, there are six separate fuses, one
each for 100, 110, 120, 220, 230 & 240 VAC po-
wer. Only one fuse is used at a time. Therefore,
for any voltage range, the two unused fuses of
the same value can be used as spares.
Location
The degausser must be placed on a flat, hard
surface. Keep at least a 15 cm (6 inch) distance
from any object that may interfere with the coo-
ling fan exhaust located on the backside of the
degausser. As a general rule, media not inten-
ding to be erased should be kept about 60 cm
(2 ft) away.
Cooling
Forced air-cooling is used to maintain safe ope-
rating temperatures within the degausser. The
air intake is located on the lower back panel and
the exhaust is located on the upper back panel.
To ensure proper cooling, do not block the air-in-
take and maintain at least a 15 cm (6“) distance
from the back of the degausser to any obstacle.
Power Supply: 95~105, 105~115, 115~125, 215~225, 225~235 or 235~240, 50/60Hz
Is pre-set in accordance with the respective site of operation.
Power Consumption:
100V: Under Standby 9.0A While charging 12.5A At the time of ERASE 0.6A
110V: Under Standby 8.5A While charging 12.0A At the time of ERASE 0.55A
120V: Under Standby 8.0A While charging 11.0A At the time of ERASE 0.5A
220V: Under Standby 4.5A While charging 7.0A At the time of ERASE 0.35A
230V: Under Standby 4.25A While charging 7.0A At the time of ERASE 0.325A
240V: Under Standby 4.0A While charging 6.5A At the time of ERASE 0.3A
Degausser System: Capacitive Discharge
Operating Time, Duty Cycle: Continuous
Erasing time: < 10 milliseconds
Cycle time: 9 seconds per cycle.
Magnetic Field: 10,000 Oe Peak ; 9,200 Oe measured in center.
Max. Media Size: 171mm (6.75 in.)(W) x 114mm (4.5 in.)(H) x 45.7mm (1.8 in.)(D)
Erasing Area Size: 171mm (6.75 in.)(W) x 114mm (4.5 in.)(H) x 45.7mm (1.8 in.)(D)
Media: 2.5 type HDD, 3.5 type HDD, DLT, LTO, 3490 and more
Temperature: 5°C - 40°C (41°F - 104°F)
Humidity: 10%H - 40%H (without condensation)
Weight: 30 kg (66 lbs.)
Shipping: 43 kg (95 lbs.)
Size:
without slide: 31.1cm (12.25 in.)(L) x 33.3cm (13.125 in.)(W) x 47.6cm (18.75 in.)(H)
with slide: 31.1cm (12.25 in.)(L) x 57.5cm (22.625 in.)(W) x 47.6cm (18.75 in.)(H)
Warranty: 2 Years Factory Warranty Standard
TECHNICAL DATA
DISPOSING OF THE MACHINE:
Dispose of the machine in an
environmentally sound fashion at the
end of its useful service life. Do not
dispose of any of the parts included
in the machine or its packaging with
household trash.
DISPOSING
90018 9 07/13