CTEK MXTS 70 - Manual (Page 3)

EN • 5
EN
INDICATION LAMPS:
START/PAUSE LAMP
Indicates that charging has not started or has been interrupted.
Press START/PAUSE-button to start/resume.
POWER LAMP
Indicates that mains supply is connected.
ERROR LAMP
Indicates that a fault has occurred.
Se ERROR CODES for description.
Press START/PAUSE-button to clear error and interrupt charging.
TEMPERATURE SENSOR LAMP
Indicates that the temperature sensor is activated.
Voltage is automatically adjusted to optimize charge at
ambient temperature.
REDUCED CURRENT LAMP
Indicates that the maximum current is limited.
SET
A
Ah & info
V
h
1 2 3 4 5 6 7 8
NORMAL
AGM
GEL
AGM
POWER
Ca/Ca SUPPLY
Amp
12V/70A
24V/35A
MXTS 70
START
PAUSE
MODE
INDICATION LAMPS, DISPLAyS
AND ERRORCODES
SET
A
Ah & info
V
h
1 2 3 4 5 6 7 8
NORMAL
AGM
GEL
AGM
POWER
Ca/Ca SUPPLY
Amp
12V/70A
24V/35A
MXTS 70
START
PAUSE
MODE
SETTINGS BEFORE START:
DISPLAy (V)
Indicates voltage set
Options: 12/24 Volts
DISPLAy (A)
Indicates current set
Options: 70/50/40/30/20 A in 12V setting
Options: 35/25/20/15/10 A in 24V setting
70A/35A could only be selected for Supply program.
For Normal-, Ca/Ca-, AGM/GEL- and AGM Power-program maximum
current is 50A/25A.
DISPLAy (h)
Indicates which parameter to set
Options: U/A/
DISPLAy (Ah & info)
Displays error codes
REAL TIME INDICATION DURING ChARGING:
DISPLAy (V)
Displays output voltage
DISPLAy (A)
Displays output current
DISPLAy (h)
Alt. 1. Displays total elapsed charging time (minutes/hours)
Alt. 2. Displays time elapsed until error occured
DISPLAy (Ah & info)
Alt.1. Displays total charge delivered since start (minutes/hours)
Alt.2. Displays error codes together with ERROR lamp
ERROR CODES:
E01 REVERSE POLARITy
Connect the charger according to “CONNECT THE CABLES”
E02 OVER VOLTAGE
Battery voltage to high for the chosen charging program, check
battery voltage.
E03 TIME OUT STEP 1: DESULPhATION
Restart the charger. If charging is still being interrupted the bat-
tery is seriously sulphated and may need to be replaced.
E04 TIME OUT STEP 2: SOFT START
Restart the charger. If charging is still being interrupted the battery
can not accept charge and may need to be replaced.
E05 TIME OUT STEP 5: ANALySE
Restart the charger. If charging is still being interrupted the bat-
tery can not keep charge and may need to be replaced.
E06 BATTERy OVERhEATED
The battery is too hot to charge. The battery is damaged and
may need to be replaced.
E07 LOW BATTERy VOLTAGE IN SUPPLy PROGRAM
Battery voltage too low or too large consumers connected. Check
if 12V battery connected in 24V battery setting or disconnect
large consumers.
E08 hIGh CURRENT IN SUPPLy PROGRAM
Check if clamps are short circuited or connected reversed polarity.
E99 OVER VOLTAGE PROTECTION
If battery voltage is below 17V the ERROR lamp is lit when 24V
setting has been selected.
Alt 1. Press START/PAUSE button to charge with 12V setting.
To set the parameters for customized charging proceed with
“CHARGING” step 5 to 8
Alt 2. Press INCREASE or DECREASE button to change to
24V setting. Press START/PAUSE button to resume. To set the
parameters for customized charging proceed with “CHARGING”
step 5 to 8.
SET
A
Ah & info
V
h
1 2 3 4 5 6 7 8
NORMAL
AGM
GEL
AGM
POWER
Ca/Ca SUPPLY
Amp
12V/70A
24V/35A
MXTS 70
START
PAUSE
MODE
SET
A
Ah & info
V
h
1 2 3 4 5 6 7 8
NORMAL
AGM
GEL
AGM
POWER
Ca/Ca SUPPLY
Amp
12V/70A
24V/35A
MXTS 70
START
PAUSE
MODE
10-70 12/24
E01-E99
E01
SET
A
Ah & info
V
h
1 2 3 4 5 6 7 8
NORMAL
AGM
GEL
AGM
POWER
Ca/Ca SUPPLY
Amp
12V/70A
24V/35A
MXTS 70
START
PAUSE
MODE
SET
A
Ah & info
V
h
1 2 3 4 5 6 7 8
NORMAL
AGM
GEL
AGM
POWER
Ca/Ca SUPPLY
Amp
12V/70A
24V/35A
MXTS 70
START
PAUSE
MODE
SET
A
Ah & info
V
h
1 2 3 4 5 6 7 8
NORMAL
AGM
GEL
AGM
POWER
Ca/Ca SUPPLY
Amp
12V/70A
24V/35A
MXTS 70
START
PAUSE
MODE
SET
A
Ah & info
V
h
1 2 3 4 5 6 7 8
NORMAL
AGM
GEL
AGM
POWER
Ca/Ca SUPPLY
Amp
12V/70A
24V/35A
MXTS 70
START
PAUSE
MODE
20015126D Manual MXTS70, All languages, Print file 003.indd 5 2011-10-11 13:01:28