WolfVision VZ-15b User Manual - Manual (Page 21)

SPECIFICATIONS
Pick-up element / video
VZ-45b
Built-in camera system 3 CCD unit - 1/2" interline transfer
Effective pixels:
Signal format:
782 (H) x 582 (V) x 3
Non-interlaced, 1/50
Resolution:
Frequency:
horizontal: 800 lines, vertical: 575 lines
Horizontal: 31.25 kHz, Vertical: 50 Hz
White balance: automatic / 3200K / 5600K / manual
Iris: automatic / manual
Optics: 8.5 x telezoom 20 - 170 mm, f = 2.0
Depth of focus: tele position: 70mm (2.75"), wide position: 250mm (9.7")
Gain control: automatic / manual 0 to 18 dB switchable
Electronic shutter: off / step / manual
Operation
Infrared remote control: functions: zoom, focus, iris, image on/off, preset 1+2
Control panel: functions: zoom, focus, iris, image on/off, light, power, preset 1+2
zoom on A5, focus on working surface level, light on, iris auto Power-on preset:
2 programmable presets: programmable settings: zoom, focus, iris, light, image
Camera control panel: functions: menu, display, functions up/down,
data up/down, white/black balance, bars,
(Reset function)
Lighting element
telezoom, electronically synchronized with camera lens
Light source:
Light/image synchronization:
24 V / 150 W halogen-lamp, 3200 kelvin (with constant spectrum !)
Spare lamp: built-in lamp changer with LED indicator
Scanning area
objects on working surface: width: 36-270mm, length: 42-360mm, height: up to 250mm
objects in a room: to eternity
Connections
RGBS (Data) output:
Preview (Data) output:
15 Pin S-VGA connector plus 5 x BNC,
(RGB: 0.7 Vpp 75
W,
Sync: 2 Vpp) switchable with Image-keys
15 Pin S-VGA connector (RGB: 0.7 Vpp 75
W,
Sync: 2 Vpp)
Constant signal output - even when image is switched off
No video outputs (DATA-RGBS only)
Video outputs (Composite, Y/C
Video RGBS or Component YUV):
Parallel port: input for external wired remote control
Serial port: configuration: RS 232, extended protocol including status report
General specifications
Power source:
Power consumption: 230 W
Working surface: reversible: one side crystalline white / one side dark grey
Weight:
Made in:
16 kg (34 lbs)
European Community (Austria)
These specifications can only be
found on WolfVision Visualizers ! Specifications and availability subject to change.
12 V DC output: for lightbox (can be switched on and off with the "light"-keys), 1.5A
90-120 V or 210-264 V AC, 50/60 Hz
SERIAL PORT
(9-pin D-Sub):
Function: ASCII-value:
Image on
Iris open
Focus plus
Zoom wide
Image off
Iris close
Focus minus
Zoom near
Power on
Power off
Preset 1
Preset 2
Light on
Light off
Menu (first use 218!)
Display / BARS
Function up
Function down
Data up / white
Data down / black
Save Preset 1
Save Preset 2
Unlock menu
Switch IR-mode A/B
Preset max. wide
Preset A4
Preset A5
Preset A6
Preset A7
Preset A8
Preset max. tele 192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
216
217
218
221
229
230
231
232
233
234
235
Detailled description of serial protocol
(including status report and position
setting) available on request from your
WolfVision dealer.
Please note that ASCII-values must
be sent as one byte (e.g. 199 and
not 1 + 1 + 9)
("ASCII"-values are sometimes
also called "HEX"-codes or
"Decimal"-codes)
* Parallel GND is the ground for the opto-isolated control inputs. DC GND is the ground
for DC + 12 V and also for Video out. If you want to use DC + 12 V for the control
inputs make a connection between DC GND and Parallel GND.
** Please note that there is no 12 V power supply when the Visualizer is in the standby
mode. For switching on the unit through the Parallel port use an external power supply
*** VZ-35b and VZ-15b only.
1 2 3 4 5 6 7 8 9 10 11 12 13
14 15 16 17 18 19 20 21 22 23 24 25
Parallel port: (25-pin D-Sub, 12-24 V) Serial port: (9-pin D-Sub)
1. Image on
2. Iris open
3. Focus plus
4. Zoom far
5. Power on
6. Preset 1
7. Light on
8. Video out ***
9. Menu 10. Function up
11. Data up/White
12. Save
13. Parallel GND*
14. Image off
15. Iris close
16. Focus minus
17. Zoom near
18. Power off 19. Preset 2
20. Light off
21. DC GND / Video GND*
22. Display / Bars
23. Function down
24. Data down / Text
25. DC + 12 V**
(male - front side)
Pins: 2:RX, 3:TX, 5:GND, 7:RTS, 8:CTS
Baud rate: 19200*, databits: 8, stopbit: 1, parity: no
Between sending codes there should be a break of at least 250ms !
(Except ZOOM, FOCUS and IRIS as the code is constantly sent as long
as these function are activated)
* It is possible to switch to 9600 baud - please contact your WolfVision dealer!
9-pin D-Sub connector
on unit, male, front side
5
9
2
7
3 4
8
1
6
CONTROL CONNECTORS (all Visualizers)
21