Rapid-Air SERVO FEED: 104CJ, 108CJ, 106CJ, 112CJ - Manual (Page 5)


operator.input.section
PROGRAmmING PROCEDURE
The intent of this section is to famil-
iarize the operator with the flow of
the program and what to expect with
each key press. each program screen
of the servo will be displayed
and also comments to clarify possible
questions. There are four sections
that will be explained and they are as
follows
section.1.—-.
. Job.number.
section.2.—-.
. manual.mode.
section.3.—-.
. automatic.mode.
section.4.—-
. reVieW.parameters.
when the servo is first started, and
has performed its startup procedure,
the first screen displayed should look
like this.
main.selection.menu:..................
. . F1=Job.num.F2=manual.
. . F3=automatic.(cYcle).
. . F4=reVieW.parameters.
*.select.F1=Job.num
The first step in programming a job is
to select a two digit job number which
will be used to store the parameters
that the operator inputs or to recall
an existing job number that was
previously loaded. when the operator
presses F1 on the keypad, the screen
will change to:
. Job.selection.menu.
. . enter.Job.number=____
. . press.F4.KeY.aFter.
. . correct.#.is.entered.
The next screen lets you program
parameters or exit with the existing
parameters.
. . Job.number.=.______
. . F1=prog..parameters
. . F4=don’t.alter.Values.
pressing the “F1 pRoG. pARAm-
eTeRS” key initiates the following
screen. key in the required param-
eters.
Feed.length=_________
. press.speed=_________
. Feed.angle=__________
*.once.the.parameters.haVe.
been.entered,.the.program.Will.
complete.the.math.routine.
Which.selects.the.proper.ac-
cel/decell.and.motor.speed.For.
the.parameters.listed.and.then.
the.main.menu.is.displaYed.
again.
*select.F2.manual
If the operator elects to move the
material from the feed to the die
electrically, the manual mode has to
be selected. pressing the F2 key will
bring up the manual mode screen.
. manual.length=_______
. F1=single_Feed
. F2=go.to.inch.mode
. F4=return
.......
each time the F1 key is pressed, the
servo will move the material the feed
length entered for the job number.
The material will move at the speed
required to keep up with the pro-
grammed press strokes per minute.
If the operator would like the material
to move a slower rate then the inch
mode should be selected. press F2
now to display the inch mode screen.
. .
. . inch.mode:
. . F1=Jog.ForWard
. . F2=Jog.reVerse
. . F4=return
when the F1 key is pressed, the feed
will advance the material at a slow
rate of speed. when the F2 key is
pressed, the feed will reverse the
material and run at a slow rate of
speed. press F4 to return to the main
screen.
with the main menu displayed and
pressing the “F3 AUTomATIC (Cy-
Cle)”, the following screen appears.
automatic....Job=01
. . Feed.length=______
. . press.speed=______
. . F4=return
In the automatic mode, the feed
length and operator entered press
speed will be displayed. whenever
the press mounted feed switch is
activated, the servo will feed the
feed length displayed on the screen.
because there is not an interface in
the control for the pilot release it will
be up to the customer to wire the pilot
release switch to the solenoid that
operates the raising of the rolls.
press F4 button to return to the main
menu and deactivate the automatic
control.
press F4 again and the final mode is
review parameters, the parameters
for the job number will then be dis-
played.
The last function on the keypad is the
“ReSeT Job pARAmeTeRS”. This
function should be used with special
Operator Input Section (cont.)