Time correction adjustment and storage/ calling, Storing the adjustment contents, Calling the stored time correction value – Alpine CDA-W560E User Manual
Page 26
24
-EN
Time Difference Table
0
0.0
14
1.4
28
2.8
1
0.1
15
1.5
29
2.9
2
0.2
16
1.6
30
3.0
3
0.3
17
1.7
31
3.1
4
0.4
18
1.8
32
3.2
5
0.5
19
1.9
33
3.3
6
0.6
20
2.0
34
3.4
7
0.7
21
2.1
35
3.5
8
0.8
22
2.2
36
3.6
9
0.9
23
2.3
37
3.7
10
1.0
24
2.4
38
3.8
11
1.1
25
2.5
39
3.9
12
1.2
26
2.6
40 - 98
4.0 - 9.8
13
1.3
27
2.7
99
9.9
Number of
Steps
Time
Difference
(ms)
Number of
Steps
Time
Difference
(ms)
Number of
Steps
Time
Difference
(ms)
5
Repeat Step 4 and set another speaker.
6
When finished with the settings, press / or -,
select EXIT, and press -/J / ENT..
The mode that is blinking at the centre of the display is the
selected mode.
• Selection of CONTINUE will cause a return to the time
correction adjustment mode.
• Selection of P-MEMORY will set the storage mode of the
adjustment value. (See “Storing the Adjustment
Contents”.)
7
Press AUDIO TUNE to return to the normal mode.
• The adjustment value in the time correction adjustment is also
reflected in the Bass Focus mode.
Storing the Adjustment Contents
1
Following Step 6 mentioned on the left within 15
seconds, press / or - to select P-MEMORY, then
press -/J / ENT..
The mode that is blinking at the centre of the display is the
selected mode.
2
Press / or - within 15 seconds, select one of
“PRESET 1” to “PRESET 6,” and press -/J / ENT..
This will store the adjusted contents in the selected
PRESET number.
3
Press AUDIO TUNE to return to the normal mode.
• The contents stored in presets 1 to 6 will be maintained even when
the unit is reset or the battery power cable is disconnected.
Calling the Stored Time Correction Value
1
Following Step 3 mentioned on the left, press / or
-, select the SELECT mode, and press -/J / ENT..
The mode that is blinking at the centre of the display is the
selected mode.
2
Press / or - within 15 seconds, select one of
“PRESET 1” to “PRESET 6,” and press -/J / ENT..
This will call the stored adjustment contents.
Time Correction Adjustment and Storage/
Calling
Before performing the following procedures, refer to “About the Time
Correction” (page 22).
1
Press AUDIO TUNE.
2
Press / or - within 15 seconds, select the time
correction adjustment mode, and press -/J / ENT..
The mode that is blinking at the centre of the display is the
selected mode.
3
Press / or - within 15 seconds, select the
ADJUST mode, and press -/J / ENT..
The mode that is blinking at the centre of the display is the
selected mode.
4
Press / or - within 15 seconds to adjust the time
correction value (0.0 to 9.9) of the first speaker
(F-L), then press -/J / ENT. to set.
B-FOCUS
(BSF)
EQ
LPF
T-CORR
(TCR)
HPF
F-L
F-R
R-L
R-R