Yokogawa JUXTA VJU7 - Manual (Page 7)

7
IM 77J01U07-01E 4th Edition Feb. 09, 2007-00
11. LIST OF PARAMETERS
No. Item Display
01 Model MODEL
02 Tag No. TAG NO
03 Self-check result SELF CHK
Display items
A Display 1 DISPLAY1
A01 Input value INPUT1
A05 Output value 1 OUTPUT1
A06 Output value 2 OUTPUT2
A07 Alarm-1 status ALM1 STATUS
A08 Alarm-2 status ALM2 STATUS
A54 Status STATUS (*1)
A56 Rev No. REV NO
A58 Menu Rev MENU REV
A60 Self-check result SELF CHK
Setting items (*2) (*3)
D Setting (I/O) SET(I/O)
D01 Tag no.1 TAG NO.1
D02 Tag no.2 TAG NO.2
D03 Comment 1 COMMENT1
D04 Comment 2 COMMENT2
D07 Input sensor type SENSOR TYPE
D08 Thermocouple type TC TYPE
D09 RTD type RTD TYPE
D15 Unit UNIT
D17 Input hard range selection SELECT RANGE
D22 Input low range INPUT1 L_RNG
D23 Input high range INPUT1 H_RNG
D30 Burnout BURN OUT
D38 Direction of output-1 action OUT1 DR
D39 Direction of output-2 action OUT2 DR
D60 Self-check result SELF CHK
Adjusting items (*3)
P Adjustment ADJUST1
P01 Wiring resistance correction WIRING R
P02 Zero adjustment of input 1 ZERO ADJ1
P03 Span adjustment of input 1 SPAN ADJ1
P12 0% adjustment of output 1 OUT1 0%
P13 100% adjustment of output 1 OUT1 100%
P14 0% adjustment of output 2 OUT2 0%
P15 100% adjustment of output 2 OUT2 100%
P60 Self-check result SELF CHK
No. Item Display
B Display
2 DISPLAY2
B01 Input value INPUT1
B05 Output value 1 OUTPUT1
B06 Output value 2 OUTPUT2
B07 Alarm-1 status ALM1 STATUS
B08 Alarm-2 status ALM2 STATUS
B60 Self-check result SELF CHK
E
Setting (alarm output) SET(ALM)
E01 Alarm-1 setting SET POINT1
E02 Alarm-2 setting SET POINT2
E03 Alarm-1 setting SET POINT1
E04 Alarm-2 setting SET POINT2
E05 Direction of alarm-1 action ALM1 ACTION
E06 Direction of alarm-2 action ALM2 ACTION
E07 Alarm-1 hysteresis HYSTERESIS1
E08 Alarm-2 hysteresis HYSTERESIS2
E09 Alarm-1 hysteresis HYSTERESIS1
E10 Alarm-2 hysteresis HYSTERESIS2
E11 Alarm-1 ON delay setting ON DELAY1
E12 Alarm-2 ON delay setting ON DELAY2
E13 Alarm-1 OFF delay setting OFF DELAY1
E14 Alarm-2 OFF delay setting OFF DELAY2
E15 Direction of alarm-1 relay action RL1 ACTION
E16 Direction of alarm-2 relay action RL2 ACTION
E60 Self-check result SELF CHK
F Setting (communication) SET(COM)
F01 Communication protocol PROTOCOL
F02 Address ADDRESS
F03 Baud rate BAUD RATE
F04 Parity PARITY
F05 Data length DATA LEN
F06 Stop bit STOP BIT
F07 Decimal point position INPUT DEC PT
F60 Self-check result SELF CHK
Test items (*3)
Q Test TEST
Q01 ON/OFF of RJC RJC
Q02 Forced output 1 OUT1 TEST
Q03 Forced output 2 OUT2 TEST
Q04 Forced output (alarm 1) ALM1 TEST
Q05 Forced output (alarm 2) ALM2 TEST
Q60 Self-check result SELF CHK
*1 : The status is displayed for service personnel to see history records.
*2 : Some items are not displayed depending on the selected input sensor type or output-2 specification.
*3 : To call the parameter setting items D, E, F, P and Q using the JHT200 Handy Terminal, execute the following operation:
Press F1 ENTER keys.
D, E, F, P or Q key enters above.