Van Air Systems FD400-FD1600 blast-pak - Manual

PAGE 1
DO NOT OPERATE THIS SYSTEM ABOVE MAXIMUM WORKING
PRESSURE (MWP) AND/OR MAXIMUM OPERATING
TEMPERATURE (
O F) SHOWN ON THE VESSEL ASME DATA
PLATE.
THIS ASME CODE VESSEL MUST BE PROTECTED BY A
PRESSURE RELIEF VALVE. Refer to OSHA 1910.169 Par. b,
Sub. Par (3) and ASME Boiler and Pressure Vessel Code,
Section VIII, Division 1, UG-125 through UG-136. Also comply
with all applicable state and local codes.
DO NOT ATTEMPT TO REMOVE OR REPAIR ANY PART OF THE
SYSTEM UNTIL IT IS COMPLETELY DEPRESSURIZED. SERIOUS
PERSONAL INJURY MAY RESULT IF THIS SAFETY RULE IS
NOT FOLLOWED.
DO NOT WELD, GRIND, OR SAND VESSEL, THIS WILL MAKE
IT UNSAFE TO OPERATE. (Note: Any alteration to the vessel
will void the ASME Code Certification and the warranty.)
INSPECT VESSEL, INSIDE AND OUT, REGULARLY FOR
BULGES, CORROSION, DENTS, GOUGES, LEAKS OR SIGNS
OF FIRE. IF DAMAGED, REMOVE FROM SERVICE
IMMEDIATELY AND NOTIFY YOUR CERTIFYING AUTHORITY.
DO NOT TRY TO TIGHTEN A LEAKING HATCH COVER.
IMMEDIATELY SHUT OFF THE AIR SUPPLY AND
DEPRESSURIZE THE SYSTEM.
DO NOT ATTEMPT TO REMOVE THE HATCH COVER UNTIL
THE SYSTEM IS COMPLETELY DEPRESSURIZED. WHEN
THE VESSEL PRESSURE IS REDUCED TO ZERO, THE
HATCH COVER CAN BE REMOVED BY HAND.
INSTALL A NEW GASKET EVERY TIME THE HATCH COVER
IS REMOVED, OR AT LEAST ONCE PER YEAR. INSPECT
THE COVER AND SEALING SURFACE FOR DAMAGE SUCH
AS CORROSION, CRACKS, OR DISTORTION. IF THERE IS
ANY DAMAGE, REPLACE COVER. REPLACE THE HATCH
COVER EVERY FIVE YEARS REGARDLESS OF CONDITION.
USE VAN AIR AUTHORIZED PARTS ONLY.
DO NOT USE POWER TOOLS OR CHEATER BARS TO
TIGHTEN THE NUT ON THE HATCH COVER. TOO MUCH
FORCE CAN DISTORT THE COVER AND/OR THE GASKET. IF
DAMAGED BY OVERTIGHTENING, THE COVER CAN BLOW
OUT AND CAUSE SERIOUS INJURY. (Note: Tighten the nut
until it is snug. When the vessel is pressurized, the pressure
on the cover will complete the seal.)
THE USE OF CHEMICALS OTHER THAN VAN AIR
DESICCANT WILL VOID THE WARRANTY ON THE BLAST
PAK.
JANUARY 2006
P/N 32-0282 rev A
OPERATION AND MAINTENANCE INSTRUCTIONS
FOR
BLAST PAK
PACKAGED COMPRESSED AIR TREATMENT SYSTEM
MODELS:
FD-400
through
FD-1600
WARNING
MODEL
FD-400
FD-800
FD-1200
FD-1600
A
77"
83-3/4"
88"
94-1/2"
B
49"
54"
60"
71-1/2"
C
26"
32-7/8"
32-7/8"
43"
D
58-9/16"
59-1/2"
60"
59-1/8"
E
72-1/8"
78-3/8"
82-5/8"
89-3/8"
MODEL
FD-400
FD-800
FD-1200
FD-1600
REGULATOR SETTING FOR AIR MOTOR
20 PSIG TO GET 1725 RPM
22 PSIG TO GET 1725 RPM
30 PSIG TO GET 1725 RPM
20 PSIG TO GET 1725 RPM
MODEL
FD-400
FD-800
FD-1200
FD-1600
INLET
2" NPT
2-1/2"NPT
2-1/2"NPT
3" NPT
OUTLET
2" NPT
2-1/2"NPT
3" NPT
3" NPT
WEIGHT
760 lbs
1155 lbs
1525 lbs
1875 lbs
DRY-O-LITE
DESICCANT *
400 lbs
500lbs
750 lbs
1000 lbs
* - ORIGINAL FILL OF DESICCANT SUPPLIED - CUSTOMER TO INSTALL