Badger Meter 330 Series Relay Transmitter - Manual (Page 2)

2
any panel using double sided adhesive tape or by attaching
fasteners through the holes in the mounting flanges of the
unit.
DIN Rail Mounting
Optional clips snap onto the mounting flanges allowing the
Series 330 to be attached to DIN 15, 32, 35 mm DIN rail
systems.
Wall Mounting
Optional metal and plastic enclosures are available to mount
the Badger Series 330 to a wall when no other enclosure is
used. The enclosure is first attached to the wall using fasten-
ers through its mounting holes.
After wiring, the transmitter may be attached to the enclo-
sure with the terminal headers facing in using the slots in
the mounting flanges. As an alternate mounting arrange-
ment, the Series 330 may be fastened to the box cover using
double-sided adhesive tape.
Series 330 Dimensions
1.50”
3.65”
3.25”
.875”
1.75”
Side 1.50”
2.75”
®
Industrial
Power
(+)
(-)
Shield
AC Load/DC +
AC Common/DC -
DIC Comm.
Port
Output
Input
®
Model: 330
SN# 0000000
NO1
NO2
NC1
NC2
Hi
Com
Lo
The Badger ® Series 330 is a compact, programmable relay
control capable of converting the signal from a Badger Meter
flow sensor into a flow switch.
With an onboard microcontroller and digital circuitry, the
Badger Series 330 is programmed from a Windows
® based
computer program. This eliminates the need to set dip
switches or potentiometers and produces precise, accurate
and drift free control of the relay outputs. In addition to
accepting the Badger Meter square wave signal, the Badger
Series 330 can accept other pulse and sine wave inputs.
The compact cast epoxy body measures 1.75” (44mm) x
2.75” (70mm) x 1.5” (38mm) and can easily be mounted to
panels, DIN rails or enclosures. With multiple inputs, ease of
use and a variety of enclosures, the Badger Series 330 is a
powerful, competitive priced relay control.
INStallatION
Mechanical installation
The Badger Series 330 transmitter may be surface mounted
onto a panel, attached to DIN rails using adapter clips or wall
mounted using two optional enclosures.
Series 330 Ordering Matrix
location
Although the Badger Series 330 device is encapsulated,
all wiring connections are made to exposed terminals.
The unit should be protected from weather and moisture
in accordance with electrical codes and standard trade
practices.
In any mounting arrangement, the primary concerns are
ease of wiring and attachment of the programming cable.
The unit generates very little heat so no consideration need
be given to cooling or ventilation.
Surface Mount Installation
The Badger Series 330 may be mounted to the surface of
Electrical Installation
All connections to the Badger Series 330 are made to screw
terminals on removable headers.
Power Supply Wiring
The Badger Series 330 requires 12-24 Volts AC or DC to
operate. The power connections are made to the ORANGE
header. The connections are labeled beside the header.
Observe the polarity shown on the label.
If a Badger Meter plug in type power supply
(Model A-1026 or A-503) is used to connect the black/white
striped wire to the terminal marked positive (+) and the black
wire to the terminal marked negative (-).
EXAMPLE: 330 - xx
Series
Programmable Local Relay Control 330
Options
Transmitter Only 00
W / NEMA 4X Enclosure 01
W / Metal Enclosure 02
W / Plastic Enclosure 03
W / DIN Rail Mounting Clips 04
Series 330 Ordering Matrix
Series 330 Optional Enclosure Dimensions
Sid e
4.5”
2.8”
2.0”
TOP
SIDE