NORD Drivesystems TI 275900210 - Manual (Page 2)

IO-Extension – SK EBIOE-2
2 TI 275900210 - 4612
Name Terminal Data
Analog output - load capacity 17 ≤ 10 mA (Mode: 0/2 … 10 V)
≤ 20 mA (Mode: 0/4 … 20 mA, at 5 V)
Analog output - specific information 17 Resolution: 10 Bit, accuracy: 0.25 V
RJ45 - current capacity RJ45 7/8 ≤ 1200 mA
Installation
Installation location Inside a suitable switching cabinet
Mounting Mounting on snap-on rail (TS 35)
Pos : 8 /T ec hnis che Inf or mationen/ IO - Er weiter ung/Ansc hlüss e [SK EBIO E-2] @ 2\ mod_1353314658836_388. doc x @ 51201 @ 6 @ 1
Connections
Terminals Screw terminals 6 terminal blocks, each with 4 connections, (5 mm spacing)
Cable cross section 0,14 … 2,5 mm AWG 14-26
PE connection via snap-on DIN
rail The snap-on rail must be earthed
Snap-on rail bus connector Plug connector For the serial installation of up to 8 SK EBIOE-2 modules
RJ45 RJ45 - socket For connection via RJ45 connection cable
Terminal Contact Designation Description
X1
Top
position 40 GND/0V Reference potential (0 V / GND)
44 VI 24V Supply voltage (+24 V - in)
78 SYS- System bus data cable -
77 SYS+ System bus data cable +
X2
Top
position 12 AGND/0V Analog Ground (internally connected to terminal 40)*
15 AIN2- Analog input 2, negative
16 AIN2+ Analog input 2, positive
17 AOUT Analog Out
X3
Top
position 12 AGND/0V Analog Ground (internally connected to terminal 40)*
13 AIN1- Analog input 1, negative
14 AIN1+ Analog input 1, positive
11 VO 10V 10 V Reference voltage
X4
Bottom
position 50 VI 24V2 Supply voltage (+24 V - in) for digital outputs
B1 DOUT1 Digital output 1
B2 DOUT2 Digital output 2
20 GND2/0V2 Reference potential (0 V / GND) of digital outputs
X5
Bottom
position 43 VO 24V Supply voltage for digital inputs (+24 V - out)
C3 DIN3 Digital input 3
C4 DIN4 Digital input 4
40 GND/0V Reference potential (0 V / GND)
X6
Bottom
position 43 VO 24V Supply voltage for digital inputs (+24 V - out)
C1 DIN1 Digital input 1
C2 DIN2 Digital input 2
40 GND/0V Reference potential (0 V / GND)
X7
Front
position RJ45 - 1 SYS + System bus data cable +
RJ45 - 2 SYS - System bus data cable -
RJ45 - 7 GND/0V Reference potential (0 V / GND)
RJ45 - 8 24 V Supply voltage (+24 V – in / out)
X8
Rear
position Snap-on rail bus
connector
Connection of voltage supply and system bus to a further
SK EBIOE - 2 module
* AGND/0V is internally connected to the reference voltage of the module GND/0V via a special
component. In order to prevent damage to the module or faults in the analog signals, the two contacts
must not be bridged
1 … 8 = X1 … X8