Canon i-SENSYS MF3010 - Manual (Page 67)

inside the machine, causing degradation in print quality.
Power Supply Requirements
220 to 240 V, 50/60 Hz
IMPORTANT
Precautions when connecting the power cord
▪ Do not connect this machine to an uninterruptible power source.
▪ Use an AC power outlet exclusively for the machine. Do not use the other sockets of the AC power outlet.
▪ Do not plug the power plug into the auxiliary outlet on a computer.
Do not use the same AC power outlet for both the machine and any of the following equipment.
- Copy machine
- Air conditioner
- Shredder
- Equipment that consumes a large amount of electricity
- Equipment that generates electrical noise
▪ When unplugging the power cord, keep interval of 5 seconds or more before plugging it again.
Miscellaneous precautions
▪ The maximum power consumption of the machine is 960 W or less.
▪ Electrical noise or a dramatic drop in supplied voltage may cause the machine or computer to operate
incorrectly or lose data.
Installation Requirements
▪ A location with suffi cient space
▪ A location with good ventilation
▪ A location with a fl at, even surface
▪ A location able to fully support the weight of the machine
IMPORTANT
Do not install the machine in the following locations, as this may result in damage to the machine.
▪ A location subject to dramatic changes in temperature or humidity
▪ A location subject to condensation
▪ A poorly ventilated location
(If you use the machine for a long time or to perform a large amount of printing in a poorly ventilated room,
the ozone or other odors generated by the machine may create an uncomfortable working environment.
In addition, chemical particles are dispersed during printing; therefore, it is important to provide adequate
ventilation.)
▪ A location near equipment that generates magnetic or electromagnetic waves
▪ A laboratory or location where chemical reactions occur
▪ A location exposed to salt air, corrosive gases, or toxic gases
▪ A location, such as on a carpet or mat, that may warp from the weight of the machine or where the machine
is liable to sink.
Maintenance and Inspections
IMPORTANT
▪ Follow the instructions in the caution label attached to this machine.
▪ Avoid shaking or applying a shock to this machine.
▪ To prevent a paper jam, do not turn the power ON/OFF, open/close the operation panel or rear cover, and
load/unload paper in the middle of printing operation.
▪ Be sure to remove the toner cartridge from the machine when transporting the machine to a distance.
▪ To avoid exposing the toner cartridge to light, place it in the protective bag included with this machine or
wrap it in a thick cloth.
▪ Clean this machine regularly. If this machine becomes dusty, it may operate improperly.
▪ The repairing parts and toner cartridges for the machine will be available for at least seven (7) years after
production of this machine model has been discontinued.
Legal Notices
Model Names
MF3010 (F162100)
WEEE Directive
Only for European Union and EEA (Norway, Iceland and Liechtenstein)
This symbol indicates that this product is not to be disposed of with your household waste,
according to the WEEE Directive (2012/19/EU) and national legislation. This product should be
handed over to a designated collection point, e.g., on an authorized one-for-one basis when
you buy a new similar product or to an authorized collection site for recycling waste electrical
and electronic equipment (EEE). Improper handling of this type of waste could have a possible
negative impact on the environment and human health due to potentially hazardous substances
that are generally associated with EEE. At the same time, your cooperation in the correct disposal
of this product will contribute to the effective usage of natural resources. For more information
about where you can drop off your waste equipment for recycling, please contact your local city
offi ce, waste authority, approved WEEE scheme or your household waste disposal service. For
more information regarding return and recycling of WEEE products, please visit
www.canon-europe.com/weee.
EMC requirements of EC Directive
This equipment conforms with the essential EMC requirements of EC Directive. We declare that this product
conforms with the EMC requirements of EC Directive at nominal mains input 230 V, 50 Hz although the rated
input of the product is 220 to 240 V, 50/60 Hz. Use of shielded cable is necessary to comply with the technical
EMC requirements of EC Directive.
International ENERGY STAR Program
As an ENERGY STAR ® Partner, Canon Inc. has determined that this product meets the
ENERGY STAR Program for energy effi ciency.
The International ENERGY STAR Offi ce Equipment Program is an international
program that promotes energy saving through the use of computers and other offi ce
equipment.
The program backs the development and dissemination of products with functions
that effectively reduce energy consumption. It is an open system in which business
proprietors can participate voluntarily.
The targeted products are offi ce equipment, such as computers, displays, printers,
facsimiles, and copiers. The standards and logos are uniform among participating
nations.
Laser Safety Information
Laser radiation could be hazardous to the human body. For this reason, laser radiation emitted inside this
equipment is hermetically sealed within the protective housing and external cover. No radiation can leak from the
machine in the normal operation of the product by the user.
This machine is classifi ed as a Class 1 Laser Product under IEC 60825-1: 2007, EN60825-1: 2007.
English
5