Document Outline

• HP ProLiant ML110 G7 Server User Guide
• Abstract
• Notice
• Contents
• Component identification
  • Front panel components
    • Front panel LEDs and buttons
  • Rear panel components
    • Rear panel LEDs and buttons
  • System board components
    • DIMM slot locations
    • System maintenance switch
    • System board LEDs
    • NMI functionality
  • SAS and SATA drive numbering
  • SAS and SATA drive LEDs
  • SAS and SATA drive LED combinations
  • BBWC module LEDs
  • FBWC module LEDs
  • Fan locations
• Operations
  • Power up the server
  • Power down the server
  • Unlock and open the tower bezel
  • Remove the tower bezel
  • Install the tower bezel
  • Remove the access panel
  • Install the access panel
  • Remove the air baffle
  • Install the air baffle
• Setup
  • Optional installation services
  • Optimum environment
    • Space and airflow requirements
    • Temperature requirements
    • Power requirements
    • Electrical grounding requirements
  • Identifying the contents of the server shipping carton
  • Installing hardware options
  • Setting up a tower server
  • Installing a server in a rack
  • Powering up and configuring the server
  • Installing the operating system
  • Registering the server
• Hardware options installation
  • Introduction
  • HP product QuickSpecs
  • SAS and SATA drive options
    • Drive installation guidelines
    • Installing a drive
  • Drive cage options
    • Four-bay LFF hot-plug drive cage option
    • Eight-bay SFF hot-plug drive cage option
  • Drive LED cable option
  • Storage controller option
  • BBWC battery/FBWC capacitor pack and module option
  • Optical drive option
  • Memory options
    • DIMM identification
    • Single-rank and dual-rank DIMMs
    • Memory subsystem architecture
    • Memory configuration
      • ECC memory configuration
      • UDIMM maximum memory configurations
      • General DIMM slot population guidelines
      • Installing a DIMM
  • Expansion board options
    • Installing an expansion board
  • Dedicated iLO management port option
    • Enabling the dedicated iLO management port
  • HP Trusted Platform Module option
    • Installing the Trusted Platform Module board
    • Retaining the recovery key/password
    • Enabling the Trusted Platform Module
  • RPS enablement option
• Cabling
  • Storage cabling
    • Four-bay LFF drive cabling
      • Non-hot-plug, SATA drive support
      • Hot-plug, SATA drive support
      • Hot-plug, SAS drive support
    • Eight-bay SFF drive cabling
  • Optical drive cabling
    • Optical drive cabling in a nonredundant power configuration
    • Optical drive cabling in a redundant power configuration
  • Battery/capacitor pack cabling
  • Power supply cabling
    • Nonredundant power supply cabling
    • Redundant power supply cabling
• Configuration and utilities
  • Configuration tools
    • SmartStart software
      • SmartStart Scripting Toolkit
    • HP ROM-Based Setup Utility
      • Using RBSU
      • Auto-configuration process
      • Boot options
      • BIOS Serial Console
    • Array Configuration Utility
    • Option ROM Configuration for Arrays
    • Re-entering the server serial number and product ID
  • Management tools
    • Automatic Server Recovery
    • ROMPaq utility
    • Integrated Lights-Out technology
    • Erase Utility
    • USB support
  • Diagnostic tools
    • HP Insight Diagnostics
    • HP Insight Diagnostics survey functionality
    • Integrated Management Log
  • Remote support and analysis tools
    • HP Insight Remote Support software
  • Keeping the system current
    • Drivers
    • Version control
    • ProLiant Support Packs
    • Operating System Version Support
    • Firmware
    • HP Smart Update Manager
    • Change control and proactive notification
    • Care Pack
• Troubleshooting
  • Troubleshooting resources
  • Pre-diagnostic steps
    • Important safety information
      • Symbols on equipment
      • Warnings and cautions
    • Symptom information
    • Prepare the server for diagnosis
      • Performing processor procedures in the troubleshooting process
      • Breaking the server down to the minimum hardware configuration
  • Loose connections
  • Service notifications
  • Server health LEDs
  • Troubleshooting flowcharts
    • Start diagnosis flowchart
    • General diagnosis flowchart
    • Server power-on problems flowchart
    • POST problems flowchart
    • OS boot problems flowchart
    • Server fault indications flowchart
  • POST error messages and beep codes
• Battery replacement
• Regulatory information
  • Safety and regulatory compliance
  • Turkey RoHS material content declaration
  • Ukraine RoHS material content declaration
  • Warranty information
• Electrostatic discharge
  • Preventing electrostatic discharge
  • Grounding methods to prevent electrostatic discharge
• Specifications
  • Environmental specifications
  • Mechanical specifications
  • Power supply specifications
• Support and other resources
  • Before you contact HP
  • HP contact information
  • Customer Self Repair
• Acronyms and abbreviations
• Documentation feedback
• Index