Kenwood RC-D710 User Manual
Page 39
PACKET-6
Command Name
Short
Description
Parameter
Default
NPATH
NPATH
Specifies digipeater call signs to be added when the
UISSID parameter in a received packet is 8 or 12.
Call1, ... call7
−
NTSGRP
NTSGRP
Specifies a group code to be used for making a
$PNTS sentence.
0 ~ 3 characters
−
NTSMRK
NTSMRK
Specifies a mark number to be used for making a
$PNTS sentence.
$00 ~ $14
$00
NTSMSG
NTSMSG
Specifies a message to be used for making a $PNTS
sentence.
0 ~ 20 characters
−
OVERKILL
OVE
Specifies the number of old messages to be deleted
when the TNC mailbox does not accept a new
message because the memory is full.
0 ~ 255
0
PACLEN
P
Specifies the maximum length of the data portion of a
packet.
0 ~ 255
128
PACTIME
PACT
If set to EVERY, sends a packet at intervals of the
specified period (n). If set to AFTER, sends a packet
only once after the specified period (n). The unit of n
is 100 milliseconds.
EVERY/ AFTER n
(n = 0 ~ 250)
AFTER 10
PERSIST
PE
Specifies a parameter to calculate probability for the
PERSIST/SLOTTIME method.
0 ~ 255
128
PPERSIST
PP
Causes the TNC to use the PERSIST/SLOTTIME
method when ON, or the DWAIT method when OFF.
ON/ OFF
ON
RAMTEST
RAMTEST Checks the RAM after clearing it.
−
−
READ
R
Specifies one or more message numbers to be read
from the TNC mailbox.
−
−
RESET
RESET
Restores the default status for all the commands.
−
−
RESPTIME
RES
Specifies the acknowledgment packet transmission
delay. The unit of the parameter is 100 milliseconds.
0 ~ 250
5
RESTART
RESTART
Causes the TNC to function as if it is switched OFF
then ON.
−
−
RETRY
RE
Specifies the number of transmission retries.
0 ~ 15
10
ROUTE
ROU
When ON and receiving a packet forwarded by a
PBBS, leaves the included route information.
ON/ OFF
ON
SENDPAC
SE
Specifies a character which forces a packet to be sent.
0 ~ $7F
$0D
SLOTTIME
SL
Specifies the period of random number generation
intervals for the PERSIST/SLOTTIME method. The
unit of the parameter is 10 milliseconds.
0 ~ 250
3
SPATH
SPATH
Specifies digipeater call signs to be added when the
UISSID parameter in a received packet is 9 or 13.
Call1, ... call7
−
STREAMCA
STREAMC
When ON and multiple connections take place,
receiving a packet causes the TNC to display the call
sign.
ON/ OFF
ON
STREAMDB
STREAMD
When ON, causes the TNC to display a stream switch
character included in a received packet.
ON/ OFF
OFF
STREAMSW
STR
Specifies a character to be used for switching streams.
0 ~ $7F
$01
TOUT
TOUT
Specifies the time-out time of the TNC mailbox. When
no packet is received within the specified time, a
disconnect takes place. The unit of the parameter is
10 seconds.
0 ~ 250
30
TRACE
TRAC
When ON, causes the TNC to display all received
packets in their entirety.
ON/ OFF
OFF
TRANS
T
Causes the TNC to exit Command mode and enter
Transparent mode. To restore Command mode, press
and hold [Ctrl], then press [C] three times.
−
−