Kenwood KDC-BT60U - Manual (Page 36)

36
| KDC-BT60U/ KDC-6047U
Audio Adjustments
“2Zone” Sets the Dual Zone System.
- Dual Zone System (page 39) . “2Zone Select”
“Preset”
Sets the audio preset.
- Audio Preset Memory (page 42) .
- Audio Preset Recall (page 43) .
( : Factory setting)
1
Select the source
Press the [SRC] button. Turn the [VOL] knob and
press it when the desired item is displayed.
Select a source other than “STANDBY”.
✍ SRC Select mode 2: Pressing the [SRC] button
repeatedly switches source.
2
Enter Audio Control mode
Press the [VOL] knob.
3
Select the setting item to adjust
Turn the [VOL] knob and press it when the
desired item is displayed.
4
Make a setting
Press the [
4] or [¢] button to select a
setting value, and then press the [VOL] knob.
5
Exit Audio Control mode
Press the [MENU] button for at least 1 second,
and then press it again briefly.
Remarks
• DSP Set
When “DSP Set” is set to “BYPASS”, the DSP function is
disabled , and the colored items can not be set.
• HIGHWAY-SOUND
Increases the volume of faintest sound being lost by road
noises to make the sound more audible. Additionally, it
accentuates bass sound being lost by road noises to make
the bass sound more dynamic.
• Supreme+ (Supreme Plus)
Technology to extrapolate and supplement with
proprietary algorithm, the high-frequency range that is cut
off when encoding. The bass and vocal sound that are cut
off by encoding are supplemented for the reproduction
of natural sound quality. Supplementing is optimized by
compression format (AAC, MP3 or WMA) and processed
according to bit rate. The effect is negligible with music
that is encoded at high bit rate, variable bit rate or has
minimal high frequency range.
The bass and vocal sound of Music CD/ iPod is also
supplemented.
• Dual Zone System
Main source and sub source (Auxiliary input) output Front
channel and Rear channel separately.
Audio Control
You can adjust following Audio Setting items.
Display Overview
“SubWoofer Level” You can set subwoofer level.
“–15” — “0” — “+15”
“DSP Set” “Bypass”: Disables the DSP function.
“Through”: Enables the DSP function.
“Equalizer” Sets the sound quality.
- Preset Equalizer curve Select (page 37) .
- Manual Equalizer Control (page 37) .
“Bass Boost” Sets the Bass Boost level in two steps.
“OFF”/ “Step1” – “2”
“HIGHWAY-SOUND” Compensates the low volume or bass sound
being lost by road noises to make vocal sound
clearer.
“OFF”/ “Step1”/ “2”/ “3”
“Supreme+” Turns ON/OFF the Supreme plus function.
Can be set while Music CD source, Audio file
source of USB and iPod source.
“ON”/ “OFF”
“Position” Compensates the sound environment in
accordance with the listening position.
- Listening Position Selection (page 38) .
- Listening Position Fine Adjustments (page
38) .
“Balance” Adjusts left/right speaker balance.
(Left) “L15” — “0” — “R15” (Right)
“Fader” Adjusts front/rear speaker balance.
(Rear) “R1”5 — “0” — “F15” (Front)
“2Zone Rear Volume” Refer to <Dual Zone System> (page 39) .
“SubWoofer” Turns on/off the subwoofer output.
“ON”/ “OFF”
“Detailed Setup”
“Car Type” To get clear sound, set the sound environment
according to the location and size of physically
installed speakers with reference to the
followings:
- Car Type Selection (page 40) .
- Speaker Setting (page 40) .
- Car Type Fine Adjustments (page 41) .
- X’Over Setting (page 42) .
“Speaker”
“Car Type Adjust”
“X'Over”
“Volume offset” Sets each source’s volume as a difference from
the basic volume.
“–8” — “±0” (AUX: “-8”— “+8”)
SRC
4
MENU VOL
¢