Document Outline

• Revision History
• Copyright
• Trademark Information
• Disclaimer of Liability
• About This Manual
  • Introduction
  • Organization
  • Intended Audience
  • Conventions
  • EU Compliance
  • Inspecting Your Shipment
• Overview
  • Features
  • Before You Begin
  • Site Preparations
    • Method of Procedure
  • Unpacking and Checking the Contents of Your Shipment
  • Required Tools and Equipment
  • Specific SG-1 Chassis Installation Requirements
    • Location Requirements
  • Power Requirements
    • SG-1 Chassis
    • Facility Requirements for AC Power
  • Blank Faceplate Requirement
  • Environmental Requirements
  • System Cabling Requirements
    • Chassis Ground and Power Cabling
    • Network Cabling
    • Configuration Port Cabling
• Installation
  • Mounting the SG-1 Chassis
  • Connecting the SG-1 Chassis Ground
  • Connecting the Power Source
    • Connecting AC Power to an SG-1 AC Chassis
  • Installing Interface Cables
    • Connecting Network Cards
    • Connecting the Ethernet Interface
    • Connecting to an Ethernet Port
  • Connecting the Craft Port Interface
  • Powering Up the SG-1
  • Installing Cards and Blank Faceplates
    • Installing Cards
    • Installing Blank Faceplates
  • Serial Cable
• Command-Line Interface (CLI)
  • Overview
  • Understanding the Interface Structure
  • Commands and Navigation
    • Command Path Navigation
  • Command-Line Editing
• Accessing the Command Line Interface
  • Connecting to the Craft Port
  • Logging on to the Craft Port
  • Setting the IP Address
    • Parameter(s)
    • Example(s)
  • Displaying the IP Address
    • Example(s)
• Using the Command Line Interface
  • Configuring the SG-1
  • Logging On
  • Logging Off
  • What to Do Next
• First-Level Commands
  • Showing a List of Available Parameters
    • Using the ? command
    • Using the show ? command
    • Using the show version command
    • Displaying the configuration in NVRAM
    • Displaying Ethernet port configurations
    • Displaying Ethernet Port Statistics
    • Displaying SONET port status
    • Displaying ATM Port Status
    • Displaying User Status
    • Displaying Routing Tables
    • Displaying System Administrators
    • Displaying System Parameters
    • Displaying License Attributes
    • Displaying VRRP attributes
    • Displaying active GRE and IP-in-IP tunnels
    • Displaying show mpls-labels commands
    • Displaying show mpls l2transport vc commands
    • Displaying a list of available write commands
    • Using the copy-TFTP command
    • Using the ping command to test network connectivity
    • Using the reload command to restart the system
    • Clearing Users
    • Using the Traceroute Command
    • Using the exit command
  • Using Debug Mode
    • Switching to Debug Mode
    • Using the show command in debug mode
    • Defining port-ethernet redundancy-mode command
    • Defining the SONET port source clock
    • Checking the system RADIUS interface
• Second Level Commands
  • Using the configure command
  • Banner Command
  • Ethernet Commands
    • Configuring Gigabit Ethernet ports
    • Configuring Ethernet Redundancy
    • Using the port-ethernet redundancy-enable command
  • Loopback Commands
    • Configuring interface loopback
  • VLAN Commands
    • Configuring the VLAN
  • Authentication Commands
    • Using the password pre-authentication command
    • Changing domain authentication settings
  • ATM Commands
    • Using the port sonet command
    • Using the pppoa enable command
    • Using the interface atm command
    • Configuring a single PVC
    • Configuring a range of PVC’s
  • RADIUS Commands
    • Configuring the RADIUS server in the SG-1 configuration
    • Configuring the RADIUS server host
    • Configuring the RADIUS proxy for native IP
    • Using the service cache command
    • Using the ip radius source-interface command
  • Access List Commands
    • Using the access-list native-ip command
    • Using the access-list native-ip-pass-through command
  • SNMP Commands
    • Using the SNMP-server community
    • Using the SNMP-server trap-source-int
  • Tunnel commands
    • Setting the no interface tunnel command
  • Timeouts Commands
  • Native IP Commands
    • Using the native-ip dhcp pre-auth-mode command
    • Using native-ip def-service-auth command
    • Using the native-ip enable command
    • Using native-ip realm command
  • Maximum Segment Size (MSS) Changing
    • Using the ip tcp adjust-mss command
  • L2TP and PPP Commands
    • Using the ip l2tp source-address command
    • PPPoE support
    • Using the pppoe enable command
  • DHCP Commands
    • Using the ip dhcp relay server command
    • DHCP Agent ID Overwrite
    • Using the ip dhcp relay agent-id-overwrite command
    • Using the ip dhcp relay advertise-protocol command
  • IGMP Commands
    • Using the ip igmp proxy command
  • Routing Command
    • Using the IP route command
    • Deleting an IP route line
    • Using the ip default-gateway command
    • Using the ip ospf interface command
    • Using the ip ospf interface hello-interval command
    • Using the ip ospf interface dead-interval command
    • Using the ip ospf interface authentication command
    • Using the ip ospf interface authentication-key command
    • Using the ip ospf interface message-digest-key command
    • Using the ip ospf area stub command
    • Using the ip ospf advertise network command
    • Using the mpls ip interface command
    • Using the mpls l2transport interface command
    • Using mpls l2transport route command
    • Using mpls ip default-route command
    • Using the vrrp command
    • Using the vrrp preempt command
  • Debug Commands
    • Configure watchdog
    • Configure time server
    • Configure error level commands
    • Debug modules
    • Debug groups
    • Trace commands
    • Configure
• SG-1 Vendor-Specific Attributes
  • Overview
    • Vendor-Specific Attributes Table
    • Hierarchical Attribute Mode
  • User Group
    • user:accounting sub-attribute
    • user:orig-name sub-attribute
    • user:auth-type sub-attribute
    • user:action sub-attribute
    • user: SSC-host sub-attribute
    • user: service-name sub-attribute
    • user:personal-site sub-attribute
    • user:mac-address sub-attribute
    • user:group sub-attribute
    • user:max-allowed-sessions sub-attribute
    • user:class sub-attribute
    • user:eds-enc-key sub-attribute
  • dhcp group
    • dhcp:dhcp-server sub-attribute
    • dhcp:opt82-relay-remote-id sub-attribute
    • dhcp:discover-action sub-attribute
  • protocol group
    • protocol:type sub-attribute
  • service group
    • service:service-timeout
    • service:next-service-name
    • service:auto-service-name
    • service:auth-source
    • service:data-quota
    • service:data-quota-used
    • service:acl-data-quota
    • service:service-cache
    • service:acl-data-quota-used
  • route group
    • route:remote-filter-redirect-gw
    • route:next-hop
    • route:nip-pipe-next-hop
    • route:advertise-protocol attribute
  • vpdn group
    • vpdn:tunnel-id attribute
    • vpdn:l2tp-tunnel-password attribute
    • vpdn:ip-address attribute
    • vpdn:tunnel-assignment-id attribute
    • vpdn:tunnel-client-ip-address
    • vpdn:nativeip sub-attribute
    • vpdn:ip-tunnel sub attribute
  • qos group
    • qos:up-mean-rate
    • qos:down-mean-rate
    • qos:acl-up-mean-rate sub attribute
    • qos:acl-down-mean-rate sub attribute
    • qos:cos
    • qos:acl-priority sub attribute
  • dns group
    • dns:ip-primary
    • dns:ip-secondary
• Redirection Server
  • Using the system event logging information includes the Http URL requests.
  • Using password command
  • Using default-redirection-site command
  • ORUP Commands
    • Using ORUP (Original Requested URL Prefix)
    • Using orup-active command
    • Using no orup-active command
  • Service Name Commands
    • Using service-name command
    • Using event-level command
  • TFTP Commands
    • Using copy-TFTP command
    • Using copy-TFTP flash def-redirection-page command
    • Using sysLog-server-ip command
  • Show Commands
    • Using show version command
    • Using show configuration command
    • Using show system command
  • Ethernet Commands
    • Using interface Ethernet command
  • Default Gateway Commands
    • Using ip default-gateway command
    • Using no ip default-gateway command
    • Format
  • Using Reload Command
  • Write Commands
    • Using write terminal command
    • Using write memory command
  • Using Poweroff Command
  • SNMP Commands
    • Using access-list SNMP-permit command
    • Using SNMP-server community command
  • Using Reset Configuration Command
  • HTTP Commands
    • Using http-proxy-server port command
  • Name Server
    • Using ip primary-name-server command
    • Using ip remote-proxy command
  • Using Hostname Command
  • Using EDS-URL-IDENTITY Command
  • Using No EDS-URL-IDENTITY Command
  • IP-IN-IP Commands
    • Using remote-ip-in-ip command
  • Show User Commands
    • Using show users command
    • Using show proc command
    • Using show memory command
    • Using show cpu command
  • Using Debug Protocol Command
  • Using Rest Web Command
  • Using Date Command
• Product Support
• Glossary
• Certification and Warranty
  • FCC Class A Compliance
  • Limited Warranty
  • Modifications
  • Safety Standards Compliance