Alto-Shaam Combitherm 4.10ESi User Manual
Page 17
CT ExpRESS INSTALLATION MANUAL • 15 .
i n s t a l l a t i o n
c t e x p r e s s ™ c h e c k l i s t
Use this list as a final check of oven installation conformance.
Damage directly attributed to improper set up, installation, or cleaning can invalidate warranty claims.
CLEARANCES:
left:
4" (152mm) — service access of 18" (457mm) recommended.
20" (508mm) from heat producing equipment.
right: 4" (102mm)
Back: 4" (102mm) for plumbing
Top:
20" (508mm) air movement Bottom: 4" (102mm) air movement
are all CLEARANCE
reQuireMenTs MeT?
YES
NO
iF no, eXplain: ________________________
________________________________________
WAtER SuppLy ANd dRAINS:
Verify hook-up to one (1) cold water supply line with a 3/4" (19mm) g
water connection supply line. Verify inlet water pressure is at a minimum
of 30 psi (2.8 bar). Maximum water pressure is not to exceed 90 psi
(6 bar). Verify drain diameter of 1-1/2" (38mm) with a positive descending
slope, and with a 2" (51mm) air gap which is free of obstructions before
connection to the site drain. Verify 1/8" (3.2mm) pitch to 10' (305cm) of
drain line.
iMporTanT: Alto-Shaam has listed Water Quality Requirements in the
installation manual for this equipment. It is the responsibility of the end
user to have the water connected to this appliance tested to ensure these
standards are met before putting the oven into use. Failure to meet these
standards will void the warranty if damage to the oven is found to be
related to water quality.
are BoTh waTer supply lines
properly connecTed?
YES
NO
iF no, eXplain: ___________________________
is a FilTer sysTeM insTalled
on This uniT?
YES
NO
sTore has seen This
recoMMendaTion:
YES
NO
signaTure oF sTore represenTaTiVe:
___________________________________________
CoNtRoL boARd CoNNECtIoNS & opERAtIoN:
ExpressTouch: with the power
on
, press the Settings Key
to access software version.
Simple Control: as unit is powered on, software
version will appear in the led display.
ALL BOARD CONNECTIONS TIGHT: YES NO
ALL FUNCTIONS ARE DISPLAYED: YES NO
ALL FUNCTIONS ON CONTROL OPERATE: YES NO
UNIT OPERATES IN ALL MODES: YES NO
iF no, eXplain: _________________________________________
pHySICAL CoNdItIoN: *
r e f e r e n c e
i n s t a l l a t i o n
i n s t r u c t i o n s
f o r
c o m p l e t e
i n f o r m a t i o n
4
Bottom of oven has been checked for damage due to improper positioning on site ...................................................
Verify all gaskets and hoses are in place and function properly ..................................................................................
Verify the installation of drip pans*, racks, shelves, drain screen, spray hose* ..........................................................
Verify the oven is level and installed on a solid, water resistant surface ....................................................................
ELECtRICAL CoNNECtIoNS:
Verify electrical power requirements for oven.
Verify voltage at terminal block.
check all terminals for tightness.
LINE VOLTAGE AT TERMINAL BLOCK (
tO
grOuNd
):
LINE 1: _________ LINE 2:_________ LINE 3: _________
LINE VOLTAGE (
phase
to
phase
): LINE 1 to 2: __________
LINE 2 to 3: __________
LINE 3 to 1: __________
ELECTRICAL SUPPLY LINE SIZE: ______________
ALL ELECTRICAL TERMINALS TIGHT: YES NO
VOLTAGE: ______________
PHASE: ______________
brEAkEr SizE: ______________
RB_____________
RECORD SOFTWARE VERSION: DB_____________
service
agency
:
start
-
up
date
:
installation
name
:
model
no
.:
serial
no
.:
tech
signature
:
customer
signature
: