A.J. Antunes & Co VCT-1000 9210727 - Manual (Page 6)

6 P/N 1010807 Rev.K 07/14
Equipment Setup
When placing the toaster into service, pay
attention to the following guidelines.
y Make sure power to the unit is off and
the toaster is at room temperature.
y Do NOT block or cover any openings
on the unit.
y Do NOT immerse cord or plug in
water.
y Keep cord away from heated surfaces.
y Do NOT allow cord to hang over edge
of table or counter.
y Connect the unit to the power supply.
Refer to the specification plate for the
proper voltage.
CAUTION
Bread may burn. Therefore toasters must
not be used near or below curtains or other
combustible walls and materials. Failure
to maintain safe operating distances may
cause discoloration or combustion.
CAUTION
All electrical connections must be in
accordance with local electrical codes
and any other applicable codes.
WARNING
ELECTRICAL SHOCK HAZARD. Failure
to follow the instructions in this manual
could result in serious injury or death.
• Electrical ground is required on this
appliance.
• Do NOT modify the power supply cord
plug. If it does not fit the outlet, have
a proper outlet installed by a qualified
electrician.
• Do NOT use an extension cord with
this appliance.
• The toaster should be grounded ac-
cording to local electrical codes to pre-
vent the possibility of electrical shock.
It requires a grounded receptacle with
separate electrical lines, protected by
fuses or circuit breaker of the proper
rating.
• Check with a qualified electrician
if you are unsure if the appliance is
properly grounded.
OPERATING
INSTRUCTIONS
1. Set the Bun Thickness Compression
Knobs (Figure 7) to the desired set-
tings.
NOTE: After initial run of 4-6 buns,
adjust controls according to the
desired finished product.
2. Turn the power on (Figure 6).
3. Turn the temperature control to 10
and allow the unit to warm up for 30
minutes.
1
2
3
4
5
1 = 1/2"(12.7mm)
2 = 5/8"(15.9mm)
4 = 3/4"(19.1mm)
5 =13/16"(20.6mm)
6 = 7/8"(22.2mm)
THICKNESS THICKNESS
1
2
3
4
5
6
6
3 =11/16"(17.5mm)
Figure 7. Bun Thickness Compression Knobs
Figure 6. Toaster Controls
BUN THICKNESS ADJUSTMENT
CONTROLS
BUN LANDING AREA
POWER SWITCH
HI-LIMIT RESET
TEMPERATURE CONTROL
(SEE FIGURE 7)
1
2
3
4
5
1 = 1/2"(12.7mm)
2 = 5/8"(15.9mm)
4 = 3/4"(19.1mm)
5 =13/16"(20.6mm)
6 = 7/8"(22.2mm)
THICKNESS THICKNESS
1
2
3
4
5
6
6
3 =11/16"(17.5mm)
RESET
BUTTON
PROTECTIVE
CAP
SAFETY FEATURES
Hi-Limit Reset Button
A Hi-Limit Control turns off electrical power
to the heater if the unit overheats. To reset
this control, allow 10-15 minutes for the unit
to cool down, Remove the Protective Cap,
and fully press the Reset Button
located at the rear of the unit (Figure 6).
4. Drop buns into toaster. Cut sides
of heel and crown must face each
other.
5. Toasted product will drop into the
bun landing area (Figure 6).
6. Test at least 4 buns before putting
toaster into service. Turn tem-
perature control to lower setting for
lighter toasting or to higher setting
for darker toasting.
7. Turn the power off when finished
toasting and
follow the daily cleaning procedures.
If the unit requires continuous resetting,
contact your Authorized Service Agency.
Conveyor interlock Safety switch
A Conveyor Interlock Safety Switch is
located on top of the unit under the Heat
Shield (Figure 1). The Conveyor Belt Chains
will not rotate unless the Heat Shield is in
place and activating the Conveyor Interlock
Safety Switch properly.