Sony DTC-A6 - Manual (Page 15)

16 EN
Writing Sub Codes
3-856-761-11(2)
Accurate Positioning of Start IDs
(Rehearsal)
1
During playback, press START ID REHEARSAL
when you arrive at the proper position.
“REHRSL” appears, “START ID” flashes in the
display and Rehearsal repeats a 3-second portion
starting from the selected position. Note that the
repeated portion will play back 8 times, with the
remaining number of times appearing to the right
of the “REHRSL”. After 8 times, the deck
automatically stops.
2 Press REW 0 or FF ) to move the beginning
of the repeated portion.
Each time you press the REW
0 or FF )
button, the beginning of the repeated portion
shifts backwards or forwards in 0.3-second
increments, up to a maximum extent of about 2
seconds (4 seconds in long-play mode) in either
direction.
Adjusting the Position of an
Existing Start ID
You can adjust the position of previously recorded
start IDs.
The time in the display shows the shift in position from
the time the START ID REHEARSAL button was
pressed.
1
During playback, press START ID REHEARSAL
when the existing start ID you want to reposition
is displayed.
The deck rewinds to the beginning of start ID and
Rehearsal repeats a 3-second portion.
2 Do Steps 1 to 3 of “Accurate Positioning of Start
IDs (Rehearsal)” on this page.
You can move the start ID to a maximum extent of
about 2 seconds (4 seconds in long-play mode) in
either direction from its original position.
Note
Start IDs written within 10 seconds from the end of the tape
may be difficult or impossible to move.
Erasing Start IDs
You can erase any start ID.
START ID REHEARSAL
MARGIN
OPEN/CLOSE
RESET
RESET MODE REW PREVIOUS FF NEXT
AMS
TIMER
START ID
PHONES SBM INPUT REC MODE
REC REC MUTE PAUSE PLAY STOP
PHONE LEVEL
REC LEVEL
RENUMBER REHEARSAL AUTO
WRITE ERASE
g
§
5 4 6
0
3 7
2 8
1 9
10
10 0
ON 48 kHz 44.1kHz LONG
ANALOG OPTICAL COAXIAL
STANDARD
OFF
REC OFF
POWER
PLAY =
p P R r (
+ 0 )
L R
ERASE
MARGIN
OPEN/CLOSE
RESET
RESET MODE REW PREVIOUS FF NEXT
AMS
TIMER
START ID
PHONES SBM INPUT REC MODE
REC REC MUTE PAUSE PLAY STOP
PHONE LEVEL
REC LEVEL
RENUMBER REHEARSAL AUTO
WRITE ERASE
g
§
5 4 6
0
3 7
2 8
1 9
10
10 0
ON 48 kHz 44.1kHz LONG
ANALOG OPTICAL COAXIAL
STANDARD
OFF
REC OFF
POWER
PLAY
=
p P R r (
+ 0 )
L R
Press ERASE when the start ID you want to erase is
displayed.
“(ERASE)” appears in the display as the deck rewinds
to the beginning of the start ID, then “ID ERASE”
appears as the deck erases the start ID.
• It takes 9 seconds to erase a start ID.
• Program numbers are erased together with start IDs.
After pressing
FF
) twice
After pressing
REW
0 twice
0 6 . S
START ID
3 Press WRITE.
“ID WRITE” appears in the display for a few
seconds and the start ID is written on the tape at
the selected position. “START ID” flashes in the
display during this time.
S
START ID
0 6 .
Movement with each press of FF )
Repeated portion
3 seconds
0.3 sec
0.3 sec
↓
Position where the START ID REHEARSAL
button is pressed in Step 1.
Movement
with each press
of REW
0