Sony MHC-771 - Manual (Page 10)

EN
Chapter 2: the CD Player 9
Playing Tracks in the
Desired Order
(program play)
You can make a program of up to
32 tracks from all the CDs in the order you
want them to be played.
1
Press FUNCTION repeatedly until “CD”
appears in the display.
2
Press § OPEN/CLOSE and place the
CDs on the disc tray. Then, press
§ OPEN/CLOSE again to close the disc
tray.
3
Press PLAY MODE repeatedly until
“PROGRAM” and “DISC” appear in the
display.
4
Press DISC 1 – 3 to choose a CD.
Playing Tracks
Repeatedly
(repeat play)
The repeat play function repeats a single
CD or all CDs in normal play, shuffle play
and program play.
Use the buttons on the unit to do this
operation.
Repeating all the tracks
1 Press REPEAT a few times until
“REPEAT” appears in the display.
2 Press fl.
To cancel repeat play
Press REPEAT so that “REPEAT” or
“REPEAT 1” disappears from the display.
5
Turn the JOG dial to choose a track.
The track number and the total playing
time appear.
6
Press ENTER/NEXT.
The chosen track number lights up inthe
music calendar. If the track number
and the total playing time disappear
before you press ENTER/NEXT, go
back to step 5.
7
Repeat steps 5 and 6 to program
additional tracks from the same CD.
Repeat steps 4 to 6 to program
additional tracks from another CD.
8
Press fl.
All the tracks play in the order you
choose.
* 1 After the last track appeared “CHECK
END” appears in the display.
* 2 “P” appears and the total playing time is
reset to 0.00.
* 3 The program is erased.
To change the order of
programmed tracks
To change the order, erase the entire
program and create a new one.
Notes
•The program you made remains in the CD
player even after it has been played back.
Press
fl to play the same program again.
•If “--.--” appears instead of the total
playing time during programming, this
means:
– you have programmed a track number
which exceeds 20, or
– the total playing time has exceeded 100
minutes.
Track number
Total playing time
To
Repeat all the
tracks on the
current CD
Repeat all the
tracks on all CDs
Repeat only one
track (in normal
play only)
Press
1/ALL DISCS
repeatedly until “1
DISC” appears in the
display.
1/ALL DISCS
repeatedly until “ALL
DISCS” appears in the
display.
REPEAT repeatedly
until “REPEAT 1”
appears in the display
while playing the track
you want to repeat.
125 63 250 500 1k 2k 4k 8k 16k(Hz)
DOLBY NR OFF
CD
DISC PROGRAM
8 VOLUME
125 63 250 500 1k 2k 4k 8k 16k(Hz)
DOLBY NR OFF
CD
CLIP REPEAT1
1 2 3 4 5
6 7 8 VOLUME
POWER nON
2
8
4
5
6
3
1
π
POWER nON
2
1
1/ALL DISCS
125 63 250 500 1k 2k 4k 8k 16k(Hz)
DOLBY NR OFF
CD
CLIP DISC PROGRAM
VOLUME
To
Check the
program
Program a pause
Stop play
Cancel program
play
Erase a track
from the end
Erase a specific
track
Erase the entire
program
Press
CHECK on the remote
repeatedly*
1
on the remote* 2
π ( on the remote)
PLAY MODE* 3
repeatedly until
“PROGRAM” or
“SHUFFLE” disappears
CLEAR on the remote in
stop mode
CHECK on the remote
repeatedly so that the
number of the track
lights up, and press
CLEAR on the remote
π ( on the remote)
once in stop mode or
twice while playing
1
CHECK
CLEAR