Sony CFD-S22 - Manual (Page 2)

1
Press CD (direct power-on).
3
Close the CD compartment.
4
Press u (N on the remote, CFD-S32/S32L only).
The player plays all the tracks once.
Track number Playing time
To
adjust the volume
stop playback
pause playback
go to the next track
go back to the previous track
remove the CD
turn on/off the player
Using the display
Checking the total track number and playing time
Press DISPLAY ENT•MEMORY in stop mode.
Checking the remaining time
Press DISPLAY ENT•MEMORY while playing a CD.
To display
the current track number and
the remaining time on the current track*
the number of tracks left
and remaining time on the CD
the current track number
and playing time
* For a track whose number is more than 20, the remaining time appears as
“- -:- -” in the display.
Locating a specific track
To locate
a specific track directly
a point while listening
to the sound
a point while observing
the display
Tip
When you locate a track numbered over 10, press >10 first, then the
corresponding number buttons.
Example:To play track number 23, press >10 first, then 2 and 3.
Note
You cannot locate a specific track if "SHUF" or "PGM" is lit in the display.
Turn off the indication by pressing x.
Repeat Play
1
Press CD.
2
Proceed as follows:
To repeat
a single track
all the tracks
tracks in random order
programmed tracks
To cancel Repeat Play
Press PLAY MODE•MONO/ST until “REP” disappears from the display.
Total track number
Total playing time
Shuffle Play
1
Press CD.
2
Press PLAY MODE•MONO/ST until “SHUF” appears in the
display.
3
Press u to start shuffle play.
To cancel Shuffle Play
Press PLAY MODE•MONO/ST until “SHUF” disappears from the display.
Programme Play
1
Press CD.
2
Press PLAY MODE•MONO/ST until “PGM” appears in the
display.
3
Press the number buttons for the tracks you want to
programme in the order you want. You can arrange the playing
order of up to 20 tracks.
4
Press u to start program play.
To cancel Programme Play
Press PLAY MODE•MONO/ST until “PGM” disappears from the display.
To check the order of tracks before play
Press DISPLAY ENT•MEMORY.
Every time you press the button, the track number appears in the
programed order.
To change the current programme
Press x once if the CD is stopped and twice if the CD is playing. The
current program will be erased. Then create a new programme following
the programming procedure.
Tips
• You can play the same program again, since the program is saved until
you open the CD compartment.
• You can record your own program. After you’ve created the programme,
insert a blank tape and press z to start recording.
Programmed track
Playing order
c
Playing a CD
Press
VOLUME +, – (VOL +, – on the remote,
CFD-S32/S32L only)
x
u (X on the remote, CFD-S32/S32L only)
Press the button again to resume play after
pause.
>
.
Z PUSH OPEN/CLOSE
OPERATE (or POWER)
Press DISPLAY ENT•MEMORY
once
twice
three times
Do this
1 Press PLAY MODE•MONO/ST until
“REP 1” appears.
2 Press the number button for the track
you want to repeat.
1 Press PLAY MODE•MONO/ST until
“REP ALL” appears.
2 Press u.
1 Press PLAY MODE•MONO/ST until
“SHUF REP” appears.
2 Press u.
1 Press PLAY MODE•MONO/ST until
“PGM REP” appears.
2 Press the number buttons for the tracks
you want to programme in the order you
want up to 20 tracks.
3 Press u.
Reinforcing the bass sound
Press MEGA BASS.
"MEGA BASS" appears in the display.
To return to normal sound, press the button again.
Adjusting the tone (CFD-S32/S32L only)
Press TONE.
To enhance
the high tone
the low tone
Tape compartment
MEGA BASS
Z PUSH OPEN/CLOSE
CD compartment
VOLUME +,–
TUNING –, +
.
, >
DISPLAY ENT
MEMORY
PLAY MODE
MONO/ST*
TONE
Location of controls
i (headphones) jack
Number buttons for
CD/RADIO DIRECT OPERATION
x
u
1
Press RADIO BAND•AUTO PRESET until the band you
want appears in the display (direct power-on).
Each time you press the button, the indication changes as
follows:
CFD-S22/S32: “FM1” n “FM2” n “AM”
CFD-S22L/S32L/922L: “FM1” n “FM2” n “MW” n
“LW”.
2
Hold down TUNING + or – (TUNE + or – on the remote,
CFD-S32/S32L only) until the frequency digits begin to
change in the display.
The player automatically scans the radio frequencies and
stops when it finds a clear station.
If you can't tune in a station, press the button repeatedly
to change the frequency step by step.
To
adjust the volume
turn on/off the radio
To improve broadcast reception
Reorient the antenna for FM. Reorient the player itself for AM or
MW/LW.
FM AM/MW/LW
Tips
• The "FM1" and "FM2" bands have the same functions. You can store the
stations you want separately in "FM1" and "FM2".
• If the FM broadcast is noisy, press PLAY MODE•MONO/ST until
"Mono" appears in the display and the radio will play in monaural.
Listening to the radio
Press
VOLUME +, – (VOL +, – on the remote,
CFD-S32/S32L only)
OPERATE (or POWER)
OPERATE
(or POWER) SLEEP
CD
Press
a number button of the track.
> (forward) or . (backward) while
playing until you find the point.
> (forward) or . (backward) in
pause until you find the point.
Display
RADIO BAND
AUTO PRESET
Display
HI
LO
Presetting radio stations
You can store radio stations into the player’s memory. You can preset up
to 30 radio stations (CFD-S22/S32) or 40 radio stations (CFD-S22L/S32L/
922L), 10 for each band in any order.
1
Press RADIO BAND•AUTO PRESET to select the band.
2
Hold down RADIO BAND•AUTO PRESET for 2 seconds
until "AUTO" flashes in the display.
3
Press DISPLAY ENT•MEMORY.
The stations are stored in memory from the lower frequencies
to the higher ones.
Tip
If you automatically preset the "FM1" or "FM2" band, 10 radio stations
are stored in "FM1" band and 10 more radio stations are stored in
"FM2" band.
If a station cannot be preset automatically
You need to preset a station with a weak signal manually.
1 Press RADIO BAND•AUTO PRESET to select the band.
2 Tune in a station you want.
3 Hold down the number buttons that you want to preset the new station
on for about 2 seconds.
The new station replaces the old one.
Playing preset radio stations
1
Press RADIO BAND•AUTO PRESET to select the band.
2
Press the number buttons to tune in the stored station.
Display
Tip
To listen through headphones, connect the headphones to the
i
(headphones) jack.
CD/RADIO DIRECT OPERATION
Display
OPERATE
(or POWER)
SLEEP
FUNCTION
Number buttons
MODE*
BAND
TUNE +, –
VOL +,–
x
X
N
. , >
LOOP
FLASH
TONE
(CFD-S32/S32L only)
MEGA BASS
Remote Control
(CFD-S32/S32L only)
* MODE on the remote has the same function
as PLAY MODE•MONO/ST on the player.
CD/RADIO DIRECT OPERATION
Display
c
Display
Enjoying Sound effects (LOOP/FLASH)
(CFD-S32/S32L only)
You can repeat part of a CD (LOOP) and can "flash" the CD sound (FLASH)
during playback.
1
Play a CD.
2
Press and hold LOOP or FLASH at the point you want to
start the function.
To Press and Hold
repeat a selected part of a CD LOOP on the remote
"flash" the CD sound FLASH on the remote
To cancel the LOOP or FLASH function
Release the button.
The player returns to normal play.
Notes on CDs
• Before playing, clean the CD with a cleaning cloth. Wipe the CD from the
center out.
• Do not use solvents such as benzine, thinner, commercially available
cleaners or anti-static spray intended for vinyl LPs.
• Do not expose the CD to direct sunlight or heat sources such as hot air
ducts, nor leave it in a car parked in direct sunlight as there can be a
considerable rise in temperature inside the car.
• Do not stick paper or sticker on the CD, nor scratch the surface of the CD.
• After playing, store the CD in its case.
If there is a scratch, dirt or fingerprints on the CD, it may cause tracking
error.
2
Press Z PUSH OPEN/CLOSE down to open the CD
compartment and place a CD in the CD compartment.
With the labeled side up
c
OPR/BATT
indicator
* The name of this button is PLAY MODE•MONO/ST for CFD-S22/S32,
PLAY MODE•MONO/ST ISS for CFD-S22L/S32L/922L.
TAPE
Adjusting the sound emphasis (MEGA BASS/TONE)
Display
Display