Sony SRS-NWZ10 - Manual

English
Before operating the unit, please read this manual thoroughly and
retain it for future reference.
WARNING
To reduce the risk of fire or electric shock, do not
expose this apparatus to rain or moisture.
To reduce the risk of electrical shock, do not open the
cabinet. Refer servicing to qualified personnel only.
To reduce the risk of fire, do not cover the ventilation of the
apparatus with newspapers, tablecloths, curtains, etc. And do not
place lighted candles on the apparatus.
To reduce the risk of fire or electric shock, do not place objects
filled with liquids, such as vases, on the apparatus.
Do not install the appliance in a confined space, such as a
bookcase or built-in cabinet.
Connect the AC power adaptor to an easily accessible AC outlet.
Should you notice an abnormality in the AC power adaptor,
disconnect it from the AC outlet immediately.
CAUTION
You are cautioned that any changes or modification not expressly
approved in this manual could void your authority to operate this
equipment.
NOTICE FOR THE CUSTOMERS IN THE U.S.A.
INFORMATION
This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This
equipment generates, uses, and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in
a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the
following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
– Consult the dealer or an experienced radio/TV technician for
help.
If you have any questions about this product, you may call;
Sony Customer Information Services Center 1-800-222-7669 or
http://www.sony.com/
Declaration of Conformity
Trade Name : SONY
Model No. : SRS-NWZ10
Responsible Party : Sony Electronics Inc.
Address : 16530 Via Esprillo, San
Diego, CA 92127 USA
Telephone No. : 858-942-2230
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1) This
device may not cause harmful interference, and (2) this device
must accept any interference received, including interference
that may cause undesired operation.
This symbol is intended to alert the user to the
presence of uninsulated “dangerous voltage”
within the product’s enclosure that may be of
sufficient magnitude to constitute a risk of
electric shock to persons.
This symbol is intended to alert the user to the
presence of important operating and
maintenance (servicing) instructions in the
literature accompanying the appliance.
Customer Support
The following URLs contain information on the latest customer
support for the speaker, and frequently asked questions and
answers.
Customers in the U.S.A.
http://www.sony.com/walkmansupport/
Customers in Canada
http://www.sony.ca/EletronicsSupport/
Precautions
For the customers in the U.S.A. and Canada
Important Safety Instructions
1) Read these instructions.
2) Keep these instructions.
3) Heed all warnings.
4) Follow all instructions.
5) Do not use this apparatus near water.
6) Clean only with dry cloth.
7) Do not block any ventilation openings.
Install in accordance with the manufacturer’s instructions.
8) Do not install near any heat sources such as radiators, heat
registers, stoves, or other apparatus (including amplifiers) that
produce heat.
9) Do not defeat the safety purpose of the polarized or
grounding-type plug. A polarized plug has two blades with
one wider than the other. A grounding type plug has two
blades and a third grounding prong. The wide blade or the
third prong are provided for your safety. If the provided plug
does not fit into your outlet, consult an electrician for
replacement of the obsolete outlet.
10) Protect the power cord from being walked on or pinched
particularly at plugs, convenience receptacles, and the point
where they exit from the apparatus.
11) Only use attachments/accessories specified by the
manufacturer.
12) Use only with the cart, stand, tripod, bracket, or table
specified by the manufacturer, or sold with the apparatus.
When a cart is used, use caution when moving the cart/
apparatus combination to avoid injury from tip-over.
13) Unplug this apparatus during lightning storms or when unused
for long periods of time.
14) Refer all servicing to qualified service personnel. Servicing is
required when the apparatus has been damaged in any way,
such as power-supply cord or plug is damaged, liquid has
been spilled or objects have fallen into the apparatus, the
apparatus has been exposed to rain or moisture, does not
operate normally, or has been dropped.
On safety
The nameplate indicating operating voltage, power consumption,
etc., is located on the bottom exterior.
• Before operating the system, be sure that the operating voltage
of the system is identical with that of your local power supply.
Where purchased Operating voltage
All countries/regions 100 – 240 V AC, 50/60 Hz
• Use only the supplied AC power adaptor.
• After operating the system with the AC power adaptor,
disconnect the AC power adaptor from the wall outlet if the
system is not to be used for an extended period of time. Just
switching the |/1 button to standby does not turn the AC power
adaptor off.
On placement
• Do not set the speaker in an inclined position.
• Do not leave the system in a location near heat sources, or in a
place subject to direct sunlight, excessive dust, moisture, rain or
mechanical shock.
On operation
• Do not open the cabinet. Refer servicing to qualified personnel
only.
• Should any solid object or liquid fall into the system, have the
system checked by qualified personnel before operating it any
further.
• Although this system is magnetically shielded, do not leave
recorded tapes, watches, personal credit cards, or floppy disks
with magnetic coding in front of the system for an extended
period of time.
On cleaning
Do not use alcohol, benzine, or thinner to clean the cabinet.
If you have any questions or problems concerning your speaker
system, please consult your nearest Sony dealer.
If the TV picture or monitor display is
magnetically distorted
Although this system is magnetically shielded, there may be cases
that the picture on some TV sets/personal computer sets may
become magnetically distorted. In such a case, turn off the power
of the TV set/personal computer set once, and after 15 to 30
minutes turn it on again. For the personal computer set, take the
appropriate measures such as data storage before turning it off.
When there seems to be no improvement, locate the system
further away from the TV set/personal computer set. Furthermore,
be sure not to place objects in which magnets are attached or used
near the TV set/personal computer set, such as audio racks, TV
stands, toys etc. These may cause magnetic distortion to the
picture due to their interaction with the system.
Identifying parts
Cradle (See fig. A)
1 WM-PORT connector (for connecting to Walkman)
2 |/1 (power/standby) indicator
3 |/1 (power/standby) button
4 MUTING indicator
5 Remote sensor
6 VOL (volume) +/– buttons
7 INPUT (audio input) jack
8 WM-PORT jack (for connecting to a PC)
9 L OUT jack
Card remote commander (See fig. B)
1 (folder) +/– buttons
2 .> (go to the beginning of the previous or next track)
buttons
3 N X (play/pause) button
4 m M (rewind/fast-forward) buttons
5 x (stop) button
6 |/1 (power/standby) button
7 MUTING (muting) button
8 VOL (volume) +/– buttons
(folder) +/– buttons find the beginning of the first track of
each group in the order selected on the Walkman.
Note
Some operations of the card remote commander may not work, or
work differently as indicated, depending on the specification of
the Walkman you are using.
Power sources
Using on house current (See fig. C)
Connect the AC power adaptor to the system.
Notes on the AC power adaptor
• Use only the supplied AC power adaptor. Do not use any other
AC power adaptor to avoid damaging the speaker.
Polarity of the plug
• Before connecting or disconnecting the AC power adaptor, turn
off the system. Otherwise, it may cause a malfunction.
Installing/Removing the
attachment
Installing the attachment (See fig. D)
Installing the attachment according to the Walkman you are using.
Insert the 2 tabs on the logo mark side in the holes of the cradle,
and then push the other side in.
Removing the attachment (See fig. E)
To remove the attachment, push at the position marked ( a a a ) on
the attachment as shown in illustration (Removing 1), or as shown
in illustration (Removing 2), while holding the Walkman
installing portion of the attachment pushed towards the rear side
of the cradle, press downwards at the position marked (
a a a ).
z Tips
• This unit can be used with a Walkman that meets the following
requirements.
– WM-PORT* (22 pin) compatible
– Supplied circular attachment
• The shape of the attachment may vary according to your
Walkman.
* WM-PORT is a dedicated multiple terminal for connecting
accessories to your Walkman.
Hooking up the unit
(See fig. F)
Connect the unit to the source device.
When the system is connected to the monaural jack of the source
device, sound may not come through the right speaker. In such a
case, use the optional* plug adaptor PC-236MS.
To connect to a stereo phone-type
headphones jack
Use the optional* connecting cord RK-G22 or connecting cord
RK-G136 and plug adaptor PC-234S.
* The above optional accessories are not provided in some areas.
Notes
• Do not carry the unit with a Walkman set on the WM-PORT
connector, as malfunction may result.
• Insert your Walkman fully into the cradle.
Preparing the card remote
commander
(See fig. G)
Before using the card remote commander for the first time,
remove the insulation film.
The battery is installed in the card remote commander at the
factory.
© 2007 Sony Corporation Printed in China
Active Speaker System
SRS-NWZ10
2-898-718-31(1)
Operating Instructions
Mode d’emploi
Manual de instrucciones
E
C
F
B
MU TIN G VO L VO L
3.2
1
2
to DC IN 12 V jack
AC power adaptor (supplied)
to wall outlet
* “WALKMAN” and “WALKMAN” logo are registered trademarks of Sony Corporation.
To INPUT jack
Portable audio
device, CD/MD
player, PC, etc.
Installing Removing 1
(rear)
Right speaker
(rear)
To LINE OUT or to
headphones jack
(stereo minijack) USB cable
(supplied with
Walkman*) RK-G136
connecting cord
(optional)
PC, etc.
D
A
MUTING VOL VO L
MU TIN G VO L VO L
Cradle (rear)
Left speaker
(rear)
To L OUT jack
To WM-PORT Jack
To R OUT jack
G
1 2
Card remote
commander (rear) lithium battery
CR2025
× 1 (optional)
Replacing the lithium
battery
(See fig. H)
The working distance of the card remote commander shortens as
the battery becomes exhausted.
Replace the battery with a new one following the procedure
below. It will last about 6 months normally.
1 Take out the battery case.
2 Replace the lithium battery CR2025 with a
new one, with the + side facing up.
3 Place the battery case back in position.
Notes on the lithium battery
• Keep the lithium battery out of the reach of children. Should the
battery be swallowed, immediately consult a doctor.
• Wipe the battery with a dry cloth to assure a good contact.
• Be sure to install the battery with the correct polarity.
• Do not hold the battery with metallic tweezers as doing so may cause
a short-circuit.
• Use of other batteries than the CR2025 may cause a risk of fire or
explosion.
WARNING
• Danger of explosion if battery is incorrectly replaced.
Replace only with the same of equivalent type.
• Battery may explode if mistreated. Do not recharge,
disassemble or dispose of in fire.
• Do not expose the battery to excessive heat such as direct
sunlight, fire or the like.
Listening to the sound
1 Disconnect the USB cable used for the unit
and personal computer, or set the POWER
switch of the connected personal computer
to OFF.
Notes
• When a USB cable is connected between the unit and a
personal computer, no sound will be heard from a Walkman set
on the WM-PORT connector.
• Depending on the computer you are using, setting the power
switch to off may not release data transfer mode.
• Sound from the device connected to INPUT jack will be heard
instead.
2 Press the |/1 button to turn on the unit.
The |/1 indicator lights up.
3 Start playing on the source device.
z Tip
The Walkman attached to the WM-PORT connector on this unit
can be controlled by the supplied card remote commander.
4 Adjust the volume.
Set the volume of the source device to moderate level, and
press the VOL +/– buttons on this unit.
Note
A beep sounds when the volume is set to minimum or maximum.
5 Press the |/1 button to turn off the unit after
use.
The |/1 indicator goes off.
Notes
• If connecting the speaker to a device with a built-in radio or tuner,
radio reception may not occur or sensitivity may be reduced
significantly.
• If the source device has a bass boost function or equalizer function,
set them to off. If these functions are on, sound may be distorted.
• If the source device’s headphone output has a line switch, better
sound will be heard if it is set to on. See the operating instructions of
the source device.
• If both a Walkman set on the WM-PORT connector and the device
connected to the INPUT jack are played at the same time, both
sounds can be heard.
• The USB cable connecting the unit with personal computer is used
for transferring Walkman’s data and recharging. When playing back
sound of a personal computer using this unit, connect through the
INPUT jack.
• If the volume level of the Walkman is high while the Walkman is
attached to the WM-PORT connector of this unit, the equalizer effect
of the speaker may be weakened.
• Sound is not output from the headphone jack of the Walkman if it is
attached to the WM-PORT connector on this unit.
Charging the Walkman
A Walkman set on the WM-PORT connector can be recharged by
either the AC power adaptor (supplied), or by using a USB cable
(supplied with the Walkman) connected to a computer.
Notes
• Insert your Walkman fully into the cradle.
• See the Operation Guide of the Walkman for details on recharging
and its related settings.
• Data transfer and recharging cannot be performed simultaneously.
• Playback and recharging can be done at the same time. Recharging
time will be longer during playback.
• Charging time varies depending on use of the AC power adaptor or
USB cable. For details, see the Operation Guide of the Walkman.
Transferring data between a
Walkman and a computer
By connecting a USB cable (supplied with the Walkman) to a
computer, you can transfer data to it from the Walkman set on the
WM-PORT connector. For details, see the Operation Guide of the
Walkman.
Notes
• If the Walkman becomes detached from the cradle during data
transfer, attach it to the cradle and start data transfer again.
• Do not connect or disconnect the USB cable or AC power adaptor
while transferring data from your computer. Your computer may not
recognize the Walkman or data transfer may be interrupted.
• While your computer is connected to the unit using a USB cable, the
Walkman attached to the WM-PORT connector does not play back
sound. The sound of the device connected to the INPUT jack will be
heard.
Recording on the Walkman
It is possible to record on a Walkman* attached to the WM-PORT
connector of this unit by connecting a source device, such as a CD
player, to the WM-PORT jack using the optional recording cable
WMC-NWR1.
* Available only when the Walkman is equipped with WM-PORT
(22 pin) and recording function.
Notes
• Recording is not possible while this unit is in standby mode.
• For details on recording, refer to the Operation Guide of your
Walkman.
Front Rear
H
Card remote
commander (rear)
1
2
1
2
Removing 2
Owner’s Record
The model number and the serial number are located on the bottom of the cradle.
Record the model number and the serial number in the space provided below.
Refer to them whenever you call upon your Sony dealer regarding this product.
Model No. SRS-NWZ10
Serial No.
Troubleshooting
Should you have a problem with your speaker system, check the
following list and take the suggested measures. If the problem
persists, consult your nearest Sony dealer.
No sound
• Disconnect the USB cable, or set the POWER switch of the
connected personal computer to OFF.
• Check that both this unit and the source device are turned on.
• Turn up the volume of the unit.
• Turn up the volume of the source device as high as possible to
the extent that sound is not distorted. For details on volume
adjustment, refer to the operating instructions supplied with the
device.
• Make sure all the connections have been correctly made.
Low sound level
• Turn up the volume of the source device as high as possible to
the extent that sound is not distorted. For details on volume
adjustment, refer to the operating instructions supplied with the
device.
• Turn up the volume of the unit.
Distorted sound
• Turn down the volume of the source device to the point where
the sound is no longer distorted. For details on volume
adjustment, refer to the operating instructions supplied with the
device.
• If the source device has a bass boosts function, set it to off.
• Turn down the volume of the unit.
There is hum or noise in the speaker output.
• Make sure all the connections have been correctly made.
• Make sure none of the audio components are positioned too
close to a TV set.
The brightness of the |/1 indicator is
unstable.
The brightness of the |/1 indicator may become unstable when
the volume is turned up. This is not a malfunction.
The battery cannot be inserted, or fits too
tightly in the Card Remote Commander.
The battery is designed so as not be inserted in the wrong
direction. Confirm polarity (+/–) and insert correctly.
Card Remote Commander operation is not
possible.
• Operate the card remote commander pointed toward the remote
sensor of the cradle.
• Remove any obstacle between the cradle and the card remote
commander.
• Avoid exposing the remote sensor of the cradle to strong light
(direct sunlight or fluorescent lamp of high frequency lighting).
• If the above remedies do not solve the problem, the battery
might be worn out. Replace it with a new one.
Specifications
Speaker section
Speaker system 2 way built-in passive radiator,
Magnetically shielded
80 mm (woofer), 25 mm (tweeter)
Impedance 3.2 Ω
Rated input power 4 W
Maximum input power 8 W
Amplifier section
Rated output 4 W + 4 W (10 % T.H.D., 1 kHz, 3.2 Ω)
Cradle section
Data input/output WM-PORT (22 pin) connector × 1,
WM-PORT (22 pin) jack × 1
Input Stereo minijack × 1
Input impedance WM-PORT (22 pin) 47 k Ω (at 1 kHz),
Stereo minijack 8 k Ω (at 1 kHz)
General
Power DC 12 V (supplied AC power adaptor)
Dimensions (w/h/d) Approx. 100 Ч 32 Ч 100 mm
(4 Ч 1 5 / 16 Ч 4 in.) (cradle)
Approx. 100 Ч 183 Ч 159 mm
(4 Ч 7 1 / 4 Ч 6 3 / 8 in.) (speaker)
Mass Approx. 100g (4 oz.) (cradle)
Approx. 950 g (2 lb. 2 oz.) (left speaker)
Approx. 930 g (2 lb. 1 oz.) (right speaker)
Supplied accessories
AC power adaptor (1)
Power cord (1)
Card Remote Commander (1)
Lithium battery CR2025 (1) (preinstalled for the trial use)
Operating Instructions (1)
Supported Walkman
WALKMAN to fulfill following requirement.
• WM-PORT (22 pin) compatible
• Supplied circular attachment
Optional accessories
Recording cable WMC-NWR1
Connecting cord RK-G22, RK-G129, RK-G136, RK-G138
Plug adaptor PC-234S, PC-236MS
The above optional accessories are not provided in some areas.
Design and specifications are subject to change without notice.
This warranty is valid only in the United States.