Sony ICF-M88B - Manual (Page 2)

RADIO POWER LIGHT ENTER/SELECT TUNE MODE BAND/SET VOL
BAND/SET TUNE MODE
RADIO POW ER
LIGHT
VOL
ENTER /SEL ECT
MPH AM
PM
FM
FREEZE PRESET
MHz
MPH
kHz
km/h inch AM
km/h
mile
CLOCK ODO DIST RT AVG MAX
mm
RADIO POWER LIGHT ENTER/SELECT TUNE MODE BAND/SET
For the initial setting
(with the radio off)
The cycle-computer needs initial set up before using.
If the wheel size you set into the cycle-computer is not suitable for using actual
wheel size, it is not possible to measure speed and distance correctly.
1 Press and hold BAND/SET for a few seconds to select “mile” or
“km”.
“mile” flashes in the display.
Each press of the ENTER/SELECT toggles between “mile” and “km”.
The unit of speed is “MPH” for miles, and “km/h” for kilometers.
Select and show the desirred unit.
2 Press BAND/SET to set a wheel size.
The wheel size flashes.
Press ENTER/SELECT repeatedly to select your wheel size (inches). Each
press changes the display as follows.
26 27 28 12 14
16 18 20 22 24
Note
The “mm” values shown on the display are approximate. Adjust the accurate size
of the wheel using Jog lever
+ or - after measuring diameter of your wheel.
It is recommend to set the wheel size in “mm” because the cycle-computer
calculates in “mm”. If you set the wheel size in “mm”, the range is from 300 to
750 mm.
Push and hold Jog lever
to change the value rapidly.
3 Press BAND/SET.
“ODO” appears in the display, and the last digit of the total distance
(odometer) flashes.
If you do not change the odometer, jump to step
4 .
To change the total distance
You can change the default setting of the total distance (odometer) using Jog
lever
+ or - (to increase or decrease) and ENTER/SELECT (to select
another digit).
4 Press BAND/SET again.
The initial setting is completed.
Tips
• When you choose the “mile”, the range is from 0.0 to 99 999.9 miles.
• When you choose the “km”, the range is from 0.0 to 159 999.9 kilometers. And
the maximum digit range is from 0 to 15.
Notes
• If you do not make any selections, for within about 65 seconds, or do press
TUNE/MODE button during the initial setting mode, the setting mode will be
canceled and the unit returns to the previous mode.
• If you press the LIGHT button for within about 65 seconds during the initial
setting mode, the setting mode will be extended.
• If you cancel during initial setting mode, the value of the unit, wheel size and
total distance entered will be erased. The unit will revert to the previous setting.
• The cycle-computer will not activate during the initial setting mode.
• If you press
RADIO POWER to turn on the unit during the initial setting
mode, the mode is canceled and the radio will activate.
• If you change the unit in the initial setting mode, the values showed in the total
distance (odometer) setting mode will be automatically converted into the new
setting unit. However, when you convert the unit from miles to kilometers, any
value over 159 999.9km is shown as 159 999.9km.
Displaying data
While cycling, current speed is always displayed and updated every second.
The highest speed that can be displayed is 124.2 MPH (199.9 km/h) and remains
displayed beyond that speed. Below 2.5 MPH (4.0 km/h), 0.0 is displayed.
Displaying the odometer
Press MODE/FREEZE repeatedly until “ODO” appears.
The current total distance is displayed.
Note
If 99 999.9 miles (160 934.3 km) is exceeded, the odometer returns to zero.
Displaying trip distance
Press MODE/FREEZE repeatedly until “DIST” appears.
At the point you want to start calculating the distance, perform the zero reset
operation.
For details on how to perform the zero reset operation, refer to “Performing the
zero reset.”
Note
If 9 999.9 miles (16 093.3 km) is exceeded, the trip distance returns to zero.
Displaying riding time
Press MODE/FREEZE repeatedly until “RT” appears.
The “Hour: Minute: Second” is indicated in the display.
At the point you want to start calculating riding time, perform the zero reset
operation. For details on how to perform the zero reset operation, refer to
“Performing the zero reset.”
Riding time is updated every second.
When one wheel revolution takes over a second, riding time is updated when the
magnet passes the sensor.
If the interval at which the magnet passes the sensor is more than 1 minute, the
calculation is canceled.
Note
If the displayed “99:59:59” is exceeded, riding time returns to zero.
Displaying average speed
Press MODE/FREEZE repeatedly until “AVG” appears.
Average speed is calculated according to trip distance and riding time.
Displaying maximum speed
Press MODE/FREEZE repeatedly until “MAX” appears.
The maximum speed recorded to date is displayed.
Note
If either trip distance or riding time returns to zero, trip distance, riding time and
average speed simultaneously return to zero.
Performing the zero reset
The zero reset operation of trip distance, riding time and average speed are
performed simultaneously and cannot reset individually.
1 Press MODE/FREEZE to display either “DIST,” “RT” or
“AVG.”
2 Press and hold RESET for a few seconds.
“DIST,” “RT” and “AVG” flash.
3 Press RESET again.
The zero reset operation is completed, and “DIST,” “RT” and “AVG” are set
to zero.
You can reset maximum speed only. Select “MAX” in step 1 , followed by step 2
and 3 .
Setting Freeze mode
You can deactivate odometer calculation, trip distance, riding time, average time,
and maximum speed (except for current speed) with the Freeze mode.
1 Press and hold MODE/FREEZE for a few seconds.
“FREEZE” lights up, and the cycle-computer enters Freeze mode.
To cancel Freeze mode, press and hold MODE/FREEZE for a few seconds.
(“FREEZE” is no longer displayed.)
Standby mode
When your bicycle is stopped with the radio off, and no button is pressed for
more than 10 minutes, the cycle-computer enters Standby mode, and only the
current time is displayed.
To cancel Standby mode
When the unit is attached to the Mount
At the point where you start and the magnet passes the sensor, or you press any
active button, Standby mode is canceled. (The display returns to the previous one
before entering Standby mode.)
When the unit is not attached to the Mount
When you attach the unit to the Mount or press any active button, Standby mode
is canceled.
Note
If the cycle-computer enters Standby mode with Freeze mode activated, Freeze
mode is not canceled.
Using the Backlight
Press LIGHT.
The backlight will light for 10 seconds. If any buttons are pressed
while the backlight is on, the backlight will turn off 10 seconds after
pressing the button.
Setting the Clock
The clock time display of this unit is a 12-hour system.
When the batteries are first installed, “AM 12:00” flashes and “CLOCK” turns on
in the display.
1 Press RADIO POWER to turn off the power.
2 Press MODE/FREEZE repeatedly until “CLOCK” appears.
3 Hold down ENTER/SELECT for more than 2 seconds until
“AM 12” starts flashing.
4 Push the Jog lever towards + or – to adjust the hour, then press
ENTER/SELECT.
The beep sounds and the minute setting starts to flash.
If you hold down the Jog lever towards
+ or – , the digit changes rapidly.
Midnight is indicated as “AM 12:00” and Noon is indicated by “PM 12:00.”
g
5 Repeat step 4 above to adjust the minutes.
“:” starts flashing and the clock starts operating.
To set the current time exactly to the second, adjust the minute setting and
then press
ENTER/SELECT to synchronize it with a time signal (such as
the telephone time signal).
Note
If you do not push the Jog lever towards + or – , or ENTER/SELECT within
about 65 seconds, the clock setting mode will be canceled.
Changing AM Channel Step
The AM channel step differs depending on area. The channel step of this unit is
factory-set to 10 kHz. Change the settings as shown below to be able to listen to
the radio.
Area Channel step
North and South American countries 10 kHz
Other countries/regions 9 kHz
Note
When the AM channel step is changed, only the preset stations on the AM band
will be initialized.
1 Press RADIO POWER to turn off the power.
2 While holding down ENTER/SELECT, keep pressing RADIO
POWER for more than 5 seconds.
Two short beeps sound, and the AM channel step will change and “9” kHz
(or “10” kHz) will light up for about 2 seconds in the display.
If you proceed to step
2 again, the channel step changes again.
Playing the Radio
— Manual Tuning
1 Press RADIO POWER to turn on the power.
2 If “PRESET” is displayed, press TUNE MODE so that
“PRESET” disappears.
Pressing TUNE MODE will switch over between manual tuning mode and
preset tuning mode.
3 Press BAND/SET to select the band.
Each press changes the band.
4 Push the Jog lever towards + or – to select the desired frequency.
If you hold down the Jog lever towards + or – , the frequency changes
rapidly.
When the frequency matches the broadcast frequency, the broadcast will be
received.
5 Adjust the volume using VOL.
To turn off the radio, press RADIO POWER .
Improving Radio Reception
FM : Set FM SENS to LOCAL if interference is
prevalent when radio wave intensity is dramatically
stronger.
Under normal conditions, set to
DX .
Presetting your Favorite
Stations
— Preset Tuning
You can preset up to 5 AM stations, and 10 FM stations. You can also delete a
preset station, whether factory-set or preset yourself.
Presetting a Station
1 Follow steps 1 to 5 in “Playing the Radio” and manually tune in to
the station you wish to preset.
2 Hold down ENTER/SELECT until the preset number flashes.
A preset number with no station will flash.
When all preset numbers have assigned stations (factory-set), "1" flashes and
"PRESET" appears.
3 Push the Jog lever towards + or – to select the number you wish to
preset, then press ENTER/SELECT.
If a preset number you select with the Jog lever has an assigned preset
station, "PRESET" appears; if no station is assigned, only the number flashes.
When you press
ENTER/SELECT , the selected preset number lights up in
the display.
Example : Preset number 2, FM 90.0 MHz
To preset another station, repeat the above steps.
To change a preset station, preset a new station. The previous station will be
canceled.
Note
If you do not perform a preset operation for about 65 seconds, presetting mode
will be canceled.
Tuning in to a Preset Station
1 Press RADIO POWER to turn on the power.
2 Press BAND/SET to select the band.
3 Press TUNE/MODE so that “PRESET” and preset number
appear.
4 Push the Jog lever towards + or – to select the desired preset
number.
5 Adjust the volume using VOL.
To turn off the radio, press RADIO POWER .
Note
If you hold down TUNE/MODE for more than 2 seconds, the unit enters the
preset station deleting mode. Press TUNE/MODE again to return to the previous
mode.
Deleting a Preset Station
1 Follow steps 1 and 3 in “Tuning in to a Preset Station”.
2 Push the Jog lever towards + or – to select the preset number to be
deleted.
3 Hold down TUNE/MODE for more than 2 seconds until
“PRESET”, “
” and the preset number flash.
preset number to be deleted
4 While the letters and the preset number are flashing, press
ENTER/SELECT.
The station set to the preset number just before the deleted station will be
displayed.
To delete other stations, repeat steps
2 to 4 .
If all the preset stations are deleted, “PRESET -” appears in the display.
To cancel deleting, press TUNE/MODE while “PRESET”, “ ” and the
preset number are flashing.
Playing the Radio on the
Mount
When the current speed is displayed (for example, after having installed the unit
on the Mount), pressing a button or the Jog lever (to perform a radio operation)
only displays the station frequency and/or current preset number. From this
display, press the
BAND/SET , TUNE/MODE or Jog lever + or - to perform the
desired radio operation.
Holding down Jog lever + or - , ENTER/SELECT or TUNE/MODE while the
current speed is displayed
Jog lever + or - : Pushing the Jog lever displays the current frequency.
Pushing and holding the Jog lever changes the frequency or
preset number.
ENTER/SELECT : Pressing this button displays the current frequency.
Pressing and holding selects the Station-presetting mode.
TUNE/MODE : Pressing this button displays the current frequency.
Pressing and holding selects preset station deleting mode in
preset tuning mode. In manual tuning mode, holding down
has no effect.
Notes
• If you perform a radio operation once in the current speed display and do not
operate the radio again within 5 seconds, the display automatically returns to
the current speed indication.
• When the radio is turned off, the current speed display appears. When the radio
is turned on, the current frequency is displayed. If you do not perform any
operation within 5 seconds, the display returns to the current speed.
• While presetting mode or deleting mode, the current speed display will not
appear. After completing or canceling the presetting/deleting mode, the current
speed display appears after 5 seconds.
VOL * FM antenna FM SENS
DX/LOCAL
Jog lever
* There is a tactile dot beside VOL to show the direction to turn up
the volume.
DX
LOCAL
FM SENS