Panasonic SCHC37EC - Manual (Page 13)

13
RQT9685
EN
GL
IS
H
Slow operation of the USB flash drive.
≥ Large file size or high memory USB flash drive takes longer time
to read.
The elapsed time displayed is different from the
actual play time.
≥ Copy the data to another USB device or backup the data and
reformat the USB device.
A beat sound or noise is heard while receiving
radio broadcast.
≥ Confirm the FM antenna is properly connected. (> 8)
≥ Adjust the position of the antenna.
≥ Try to keep a certain amount of distance between the antenna and
AC mains lead.
≥ Try to use outdoor antenna if there are buildings or mountains
nearby.
≥ Switch the television or other audio player off or separate it from
the unit.
≥ Keep this unit away from mobile phones if the interference is
apparent.
Cannot charge or operate.
≥ Check that the iPod/iPhone is connected firmly. (> 8)
≥ The battery of the iPod/iPhone is depleted. Charge the iPod/
iPhone, and then operate again.
≥ When unexpected operation occurs while using the iPod/iPhone,
connect the iPod/iPhone again or try to restart the iPod/iPhone.
The remote control doesn't work properly.
≥ The remote control and this unit are using a different code.
(> right, “REMOTE ”)
The following messages or service numbers may
appear on the unit's display.
“--:--”
≥ You plugged the AC mains lead in for the first time or there was a
power failure recently. Set the time (> 11).
“ADJUST CLOCK”
≥ Clock is not set. Adjust the clock accordingly.
“ADJUST TIMER”
≥ Play timer is not set. Adjust the play timer accordingly.
“AUTO OFF”
≥ The unit has been left unused for about 30 minutes and will shut
down in a minute. Press any button to cancel it.
“CANNOT SET”
≥ Select an audio source other than “VTUNER”.
“CHECKING CONNECTION”
≥ The unit is checking the connected iPod/iPhone. If this display
keeps appearing, make sure that iPod/iPhone is inserted correctly
and try again (> 8).
“ERROR”
≥ Incorrect operation is performed. Read the instructions and try
again.
“F61”
≥ There is a power supply problem. Consult the dealer.
“ILLEGAL OPEN”
≥ Sliding door is not in correct position. Turn the unit off and on
again. If this display appears again, consult the dealer.
“IPOD OVER CURRENT ERROR”
≥ The iPod/iPhone is drawing too much power. Remove the iPod/
iPhone and turn the unit off and on again.
“NODEVICE”
≥ The iPod/iPhone device is not inserted correctly. Read the
instructions and try again (> 8).
≥ The USB device is not inserted. Check the connection.
“NO DISC”
≥ Insert the disc to be played (> 8).
“NO PLAY”
≥ A CD disc that is not in CD-DA or MP3 format is inserted. It cannot
be played.
≥ If there are more than 255 albums or folders (audio and
non-audio), some of the MP3 files in these albums may not be
read and played. Transfer these music albums to another USB.
Alternatively, reformat the USB device and save these music
albums prior to saving the other non-audio folders.
“NOT SUPPORTED”
≥ You have inserted an iPod/iPhone that cannot be played (> 4).
Insert correctly and try again if iPod/iPhone is compatible.
≥ If the iPod/iPhone is compatible, turn it on before inserting it to this
unit.
“READING”
≥ The unit is checking the CD information. After this display has
disappeared, start operating.
“START ERROR”
≥ Check the iPhone/iPod touch.
Visit the below website for more information:
http://radio.vtuner.com/panasonic/en/
“REMOTE ” (“ ” stands for a number.)
≥ The remote control and this unit are using different codes. Change
the code on the remote control.
– When “REMOTE 1” is displayed, press and hold [OK] and
[4] for more than 4 seconds.
– When “REMOTE 2” is displayed, press and hold [OK] and
[3] for more than 4 seconds.
“USB OVER CURRENT ERROR”
≥ The USB device is drawing too much power. Switch to “CD”
mode, remove the USB and turn the unit off.
Radio
iPod/iPhone operations
Remote control
Messages
SC-HC37~RQT9685.book Page 13 Friday, February 24, 2012 9:45 AM