Panasonic CYVMR5800N - Manual (Page 7)

No. Item Diagram Q’ty
1
2
Color LCD monitor
Power connector
(Length: 3 m)
1
1
E
N
G
L
I
S
H
9
CY-VMR5800N
14
Installation Guide
WARNING
The installation information is designed for experienced installers and is not intended
for non-technical individuals. It does not contain warnings or cautions of the potential
dangers involved in attempting to install this product.
Any attempt to install this product in a motor car by anyone other than a qualified
installer could cause damage to the electrical system and could result in serious per-
sonal injury or death.
❐ Installation Hardware ❐ Overview
This product should be installed by a professional.
(Please refer to the “WARNING” statement
above.)
≥ Identify and label the car wires.
≥ Connect the car wires to the wires of the power
connector.
≥ Check the operation of the unit.
≥ If you do not use the metal fitting body
(CA-FN10X, optional), please purchase your
favorite kits for the display unit installation and
consult your nearest professional installer.
≥ If you encounter problems, please consult your
nearest professional installer.
E
N
G
L
I
S
H
10
CY-VMR5800N
15
12 V DC test
bulb
Electrical tape Slide-cut
pliers
❐ Identify All Leads
The first step in installation is to identify all the car
wires you’ll use when hooking up your LCD monitor.
As you identify each wire, we suggest that you label
it using masking tape and a permanent marker. This
will help avoid confusion when making connections
later.
Note:
≥
Do not connect the power connector until you
have made all connections. If there are no plastic
caps on the hooking wires, insulate all exposed
leads with electrical tape until you are ready to use
them. Identify the leads in the following order.
Power Lead
If your car has a radio or is pre-wired for one:
Cut the connector wires one at a time from the plug
(leaving the leads as long as possible) so that you
can work with individual leads.
Turn on the ignition to the accessory position, and
ground one lead of the test bulb to the chassis.
Touch the other lead of the test bulb to each of the
exposed wires from the radio connector plug. Touch
one wire at a time until you find the outlet that caus-
es the test bulb to light.
Now turn the ignition off and then on. If the bulb also
turns off and on, that outlet is the car power lead.
If your car is not wired for an audio unit:
Go to the fuse block and find the fuse port for acces-
sory (ACC), or ignition (IGN).
❐ Required Tools
You’ll need the following:
❐ Before Installation
WARNING
≥
Do not install the monitor in a location which
obstructs driving, visibility or which is prohibit-
ed by applicable laws and regulations.
If the monitor is installed in a location which
obstructs forward visibility or operation of the air
bag or other safety equipment or which interferes
with operation of the car, it may cause an acci-
dent.
≥ Never use bolts or nuts from the car’s safety
devices for installation.
If bolts or nuts from the wheel, brakes or other
safety devices are used for installation of the mon-
itor, it may cause an accident.
≥ Attach the wires correctly.
If the wiring is not correctly performed, it may
cause a fire or an accident. In particular, be sure to
run and secure the lead wire so that it does not get
tangled with a screw or the moving portion of a
seat rail.
≥ Use with 12 V DC negative ground car.
This unit is only for use with a 12 V DC negative
ground car. It cannot be used in large trucks or
diesel cars which are 24 V DC car. If it is used in
the wrong type of car, it may cause a fire or an
accident.
Caution:
≥
This unit operates with a 12 V DC negative
ground auto battery system only. Do not
attempt to use it in any other system. Doing so
could cause serious damage.
Before you begin installation, look for the following
items which are packed with your unit.
≥ Warranty card…Fill this out promptly.
≥ Installation hardware…Needed for monitor set-
ting.
Cautions:
≥
Use the specified fuse.
Be sure to always use the specified fuse. If a
fuse other than the specified fuse is used, it
may cause a fire or an accident.
≥ Do not damage the cord by pinching or pulling
it.
Do not pull or damage the cord. If the cord is
not treated properly, it will short out or be sev-
ered and may cause a fire or an accident.
PO W ER ASP EC T PI CT UR E BR IG HT M EN U EN TE R # "