CatEye CC-AT200W [Adventure] User Manual

Cateye adventure, Cyclocomputer cc-at200w, 0678 eng

Advertising

CATEYE ADVENTURE

CYCLOCOMPUTER CC-AT200W

0678

ENG

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two condi-

tions:(1)This device may not cause harmful interference, and (2) this device must accept any inter-

ference received, including interference that may cause undesired operation.

Modifications

The FCC requires the user to be notified that any changes or modifications made to this device that are

not expressly approved by CatEye Co., Ltd. May void the user ’s authority to operate the equipment.

L mm

SSE

MODE

MENU

MODE+SSE

MODE

Tire circumference

reference table

ETRTO Tire size

(

)

47-203 12x1.75

935

54-203 12x1.95

940

40-254 14x1.50

1020

47-254 14x1.75

1055

40-305 16x1.50

1185

47-305 16x1.75

1195

54-305 16x2.00

1245

28-349 16x1-1/8

1290

37-349 16x1-3/8

1300

32-369 17x1-1/4

(

369

)

1340

40-355 18x1.50

1340

47-355 18x1.75

1350

32-406 20x1.25

1450

35-406 20x1.35

1460

40-406 20x1.50

1490

47-406 20x1.75

1515

50-406 20x1.95

1565

28-451 20x1-1/8

1545

37-451 20x1-3/8

1615

37-501 22x1-3/8

1770

40-501 22x1-1/2

1785

47-507 24x1.75

1890

50-507 24x2.00

1925

54-507 24x2.125

1965

25-520 24x1

(

520

)

1753

24x3/4

Tubuler

1785

28-540 24x1-1/8

1795

32-540 24x1-1/4

1905

25-559 26x1

(

559

)

1913

32-559 26x1.25

1950

37-559 26x1.40

2005

40-559 26x1.50

2010

47-559 26x1.75

2023

50-559 26x1.95

2050

54-559 26x2.10

2068

57-559 26x2.125

2070

58-559 26x2.35

2083

75-559 26x3.00

2170

28-590 26x1-1/8

1970

37-590 26x1-3/8

2068

37-584 26x1-1/2

2100

650C Tubuler

26x7/8

1920

20-571 650x20C

1938

23-571 650x23C

1944

25-571 650x25C

26x1

(

571

)

1952

40-590 650x38A

2125

40-584 650x38B

2105

25-630 27x1

(

630

)

2145

28-630 27x1-1/8

2155

32-630 27x1-1/4

2161

37-630 27x1-3/8

2169

18-622 700x18C

2070

19-622 700x19C

2080

20-622 700x20C

2086

23-622 700x23C 2096

25-622 700x25C

2105

28-622 700x28C

2136

30-622 700x30C

2146

32-622 700x32C

2155

700C

Tubuler

2130

35-622 700x35C

2168

38-622 700x38C

2180

40-622 700x40C

2200

42-622 700x42C

2224

44-622 700x44C

2235

45-622 700x45C

2242

47-622 700x47C

2268

54-622 29x2.1

2288

60-622 29x2.3

2326

SENS

5 mm

SENSO

ZONE

SENS

ZONE

SENSOR

ZONE

4 5

WARNING / CAUTION

Do not concentrate on the computer while riding. Ride safely!

•

Install the magnet, sensor, and bracket securely. Check these periodically.

•

If a child swallows a battery, consult a doctor immediately.

•

Do not leave the computer in direct sunlight for a long period of time.

•

Do not disassemble the computer.

•

Do not drop the computer to avoid malfunction or damage.

•

When using the computer installed on the bracket, change the

•

MODE by pressing on the four

dots below the screen, or by pressing on the SSE simultaneously, to start or stop the timer.

Pressing hard on other areas may result in malfunction or damage to the computer.

Be sure to tighten the dial of the FlexTight bracket by hand. Tightening it strongly using a

•

tool, etc. may damage the screw thread.

When cleaning the computer, bracket and sensor, do not use thinners, benzene, or alcohol.

•

A temperature sensor is built in the computer. If the sensor is heated by direct sunlight or

•

body heat, it may not indicate the temperature correctly.

The altitude data with this unit is for reference only; accordingly, do not use this unit as a

•

measuring device for professional use.

Dispose of used batteries according to local regulations.

•

LCD screen may be distorted when viewed through polarized sunglass lenses.

•

Wireless Sensor

In order to prevent any interference with the sensor signal, the transmission range is designed

to be 20 to 70 cm, in addition to use of the ID code. (This receiving range is only a reference.)

Please note the following points.

To use this unit, the sensor ID has to be set.

•

Two different IDs,

•

ID1 and ID2, can be registered to this unit, which are identified automatically.

The computer cannot receive when the distance between the sensor and computer is too long.

•

Temperature drop and battery drain may worsen the receiving sensitivity even if they are within

the transmission range.

Interference may occur, resulting in incorrect data, if the computer is:

Near a TV, PC, radio, motor, or in a car or train.

•

Close to a railroad crossing, railway tracks, TV stations and/or radar base.

•

Using with other wireless devices, or some particular battery lights.

•

Before using the computer, please thoroughly read this manual and keep

it for future reference.

When using the computer for the first time or resetting to the factory

default setting, format according to the following procedure.

Format (initialize)

1. Press and hold the MENU button.

2. Press the AC button.

3. Release the AC button.

4. Release the MENU button.

Select the speed and temperature unit

When MODE and SSE are pressed simultane-

ously, “Speed unit” or “Temperature unit” can be

selected. Select “km/h” or “mph” for the speed

unit, and “°C” or “°F” for the temperature unit.

Press MENU to register.

Enter the tire circumference

Enter the tire circumference of your bicycle in mm.

Refer to the tire circumference reference table.

Set the sensor ID

Hold the computer body close to the sensor (20

- 70cm), and press and hold the RESET but-

ton on the sensor with a sharp object. Sensor

will randomly generate an ID number for the

computer body to receive, and displays on the

screen. If successfully synchronized, screen will

automatically move on to Clock setting screen.

When setting the sensor ID, place the sensor at least 20 cm (approxi-

mately 8 inches) away from the computer. Press and hold the RESET

button, the sensor will send the ID when releasing the button.
The computer is on standby for 5 minutes while setting the sensor ID. It dis-

plays “ERROR”, and cancels the ID when no ID signal is received during the

standby, or you press MODE and SSE simultaneously. Screen will move on to

clock setting. Without the ID, speed cannot be detected and displayed. Be sure

to set the sensor ID according to “Sensor ID setting” on the menu screen.

Original ID is saved if you cancel the ID.

Set the clock

When MODE and SSE are pressed simultane-

ously, “Displayed time”, “Hour”, and “Minute”

will appear, in this order.

Measure wheel circumference (L) of your bike
To get the most accurate calibration do a wheel roll out. With the valve stem

perpendicular to the ground, mark the pavement at the valve stem. With the

riders weight on the bike, roll the wheel one tire revolution in a straight line

and mark the ground when the valve stem is perpendicular to the ground

again. Measure the distance in millimeters. This is the most accurate wheel

calibration number.

How to restart

After changing the battery, or when the computer displays an error, restart the com-

puter according to the following procedure.

Press the

AC button on the back of the computer.

Set the clock. Refer to “Preparing the computer 5”.

The stored sea level altitude, home altitude, speed unit, wheel size, sensor ID, countdown dis-

tance, selected wheel, AT setting, total distance and total altitude gain will not be changed after

pressing the AC button.

Preparing the computer

How to install the unit on your bicycle

Bracket band

Bracket

Nut

Sensor

Magnet

Sensor rubber pad

Bracket rubber pad

Nylon ties (x2)

MENU

Unit

selection

Increase

the value

Move digits (By press-

ing simultaneously)

the setting

(Finish)

Move to Clock

Setting when no

ID has been set

24h ↔ 12h,

or increase

the value

Switch the screen

or move digits

(By pressing

simultaneously)

Switch the screen (By

pressing simultaneously)

Cancel the ID or

reset (By pressing

simultaneously)

Start the ID set-

ting (By press-

ing & holding)

MENU

MODE

MODE+SSE

MODE

MENU

MODE+SSE

MODE

Battery case cover

Pressure sensor

Press the

SSE button with

the computer body together.

SSE button by itself does

not function.

Press only the computer

body.

Operation of buttons when the computer is

mounted on the bracket

km/h mph

: Speed unit

: Wheel size icon

: Sensor signal reception icon

MODE+SSE

Click

RESET

Install the sensor and magnet

The clearance between

the sensor and mag-

net is 5 mm or less.

The magnet passes

through the sensor zone.

The distance from

the computer to the

sensor is within the

transmission range.

Sensor zone

Right front fork (inside)

The magnet may be installed anywhere on the spoke if the

above installation conditions are satisfied.

Max

70 cm

Install the sensor

Right front fork

Install the sensor to the front fork as high as possible.

Pull securely

Install the magnet

Spoke on the right

To the sensor zone

Attach the bracket to the stem or handlebar

When attaching the bracket to the stem

Stem

When attaching the bracket to the handlebar

On account of the receiving sensitivity, attach the

bracket so that the computer is kept horizontal. Handlebar

Click

While supporting it by hand,

For wing type handlebar or oversized stem,

bracket can be mounted using the Bracket

Holder and nylon ties. (Option)

push it out as if lifting the front up

Cut

Caution:

Round off the cut edge

of the bracket band to

prevent injury.

Remove/install the computer

After installation, check that the speed is displayed on the computer when gently turning the

front wheel. When it is not displayed, check the positions of

, and

Advertising

Popular Brands

Popular manuals