Vaddio Quick-Connect Universal CAT-5 - Manual (Page 8)

WallVIEW Universal CCU Cat-5 Version
Vaddio WallVIEW Universal CCU Cat-5 Version. Document Number 342-0512 Rev C Page 8 of 20
Image: Close up View of the Universal CCU HD-19 Control Panel
HD-18/HD-20 Keypad Controls from (left to right): Touch the button with the parameter to be controlled and adjust the value with the
encoder, then touch the cancel button to exit.

Scenes A, B & C: Three camera adjustment scenes (A, B & C) can be stored into microprocessor memory. When lit
(backlit blue button), the scene is activated. To store a scene, the user adjusts the controls and touches and holds the
scene button down until the button blinks. To erase a scene press and hold the scene button and the cancel button.

Auto White Balance: The Automatic White Balance controls/adjusts the color levels automatically when engaged. Take
it out of Auto to manually adjust the Red and Blue levels.

OPWB (One Push White Balance): When using OPWB, zoom in on a white subject, at least 60% of the image must be
white, touch the OPWB button and the coloration of the image will adjust to the white used in this shot.

Red & Blue Gain Controls: The Red and Blue Gain buttons in combination with the encoder adjust the red and blue
gain of the signal when Auto White Balance is disengaged.

Chroma: Chroma controls the overall color of the image being captured.

Bright: This is the overall luminance control for the image.

Gamma: Gamma adjusts the overall brightness of an image to compensate for the perception of luminance and chroma.

Detail: The Detail control sharpens or softens objects in the frame. Works well when looking at text.

IRIS - Auto or Manual: The Auto Iris mode automatically adjusts the iris and gain of the camera. To manually adjust the
iris or gain, turn off this control. The Manual Iris control allows the user to set the iris manually to one of the several
settings available

Gain: The Gain control boosts the signal level when the iris is open all the way, and there is not enough lighting
available. To manually adjust the Gain, Auto Iris must be off. Use the Gain last to enhance the image.

Rotary Encoder: Use the encoder to adjust values after the button is selected. This makes for very quick changes.

The Menu Buttons: There are other screens to be accessed other than the camera control screen. Use the SELECT
and CANCEL to enter other controls and exit other menus.
Image: Rear Panel Connection and Controls (left to right)

Power Supply Input: The Universal CCU uses a 36VDC, 2.78 Amp power supply on a 5.5mm OD x 2.5mm ID coaxial
connector.

36 VDC to Camera - RED RJ-45: Power is provided on a Cat-5 cable to EZIM (EZCamera Interface Module) Slot Card.
The power is regulated in the camera to 12 VDC.

RS-232 IN - GREEN RJ-45: RS-232 Input from ProductionVIEW™ console, Precision Camera Controller or other PTZ
controller. Daisy Chain control is not supported.

RS-232 to Camera - BLUE RJ-45: RS-232 over Cat-5 provides control signals to the camera.

Tally on 2-pin Molex 5.0mm Euro-Style connector: A contact closure lights the blue LED on front panel showing
which Universal CCU and camera combination is the live Program in a multi-camera CCU installation. A tally command
will also be sent to the camera via RS-232 to illuminate the LED on the cameras that have on-board tally lights.

Camera Feature Switches: The CCU interface has an 8-position dip switch on the rear panel to allow for certain
functionality. All switches should be in the down position for default.
Dip Switch 1: Put up to allow Scene A to load upon start-up or boot up.
Dip Switch 5: Put up to access LCD Display Menu settings including Display Mode, Bias and Contrast.

Video from Camera - YELLOW RJ-45: The yellow RJ-45 receives the camera’s four (4) differential video signals from
the EZIM Slot Card to the Quick-Connect CCU on Video Cat-5 cable.

HD Video Outputs: The Universal CCU has 3 (three) simultaneous video output formats that are the same resolution as
the video inputs providing the ultimate in connectivity flexibility. The output formats include:

HD YPbPr on DE-15-F (HD15) - (supports up to/and including 1080p/60 - not limited at 1080i/59.94)

HDMI on HDMI-F (supports up to and including 1080p/60)

HD-SDI on Edge Mount Carrier Class, Gold BNC-F (supports 3Gb/s Single Link 1080p/60 HD-SDI)
The universal CCU supports all the resolutions of the HD-20, HD-19 and HD-18 PTZ cameras.