Full Throttle Skidoo 007-1024 - Manual

Revised May 2013
CAUTION: INSTALLATION IS ALWAYS AT YOUR OWN RISK.
Improper assembly of this device may result in serious injury or even death, not to mention catastrophic damage to your machine. Before beginning, you
must carefully read ALL INSTRUCTIONS, as well as attached DISCLAIMER INFORMATION. If you have any questions, no matter how silly, consult an
professional mechanic or call to speak with one of our Technical Advisors at (509) 927-7533. While installation is quite simple, it should ONLY be
performed by those possessing solid mechanical abilities.
IF YOU ARE NOT MECHANICALLY INCLINED WE RECOMMEND YOU SEEK OUT EITHER A PROFESSIONAL
MECHANIC OR YOUR DEALER TO INSTALL THE GOLDFINGER ON YOUR SNOWMOBILE!
TOOLS NEEDED
Other than the tools supplied with kit, you should only need:
✦ a pair of diagonal cutters (dikes) to trim excess cable
✦ a pair of slip-joint pliers
✦
1 tube Blue Loctite
PARTS LIST
A. Stainless steel adaptor clip (1)
B. Short allen bolt (1)
C. Barrel bolt (1)
D. Aluminum cable crimp cap (1)
E. Shiny chrome ferrule end (2)
F. Cable (1)
G. Allen wrenches (3, sizes 2.5mm, 3mm, 4mm)
H. Zip tie (4)
I. Rubber accordion boot (1)
J. Washers (5)
K. Cable housing (1)
L. GOLDFINGER lever and perch with safety pin installed (1)
A) Installation of Left-Side Throttle Lever Perch (See Photo A)
On most models the throttle lever perch will fit over the left side handlebar grip with no modifications to the grip.
The goal for this section will be to position the throttle lever perch assembly as closely as possible to the left side
of the brake reservoir/switch switch housing on the left side of handlebars, with the lever hanging straight down.
1) Using smallest (2.5mm) allen wrench supplied in kit, remove the 2 lever perch allen screws, then remove the
perch cap.
2) Position lever perch and cap over handlebar grip as closely as possible to the left side of the brake reservoir/
switch housing assembly on the left side of handlebars. The GOLDFINGER lever should hang in
approximately the 6:00 position, or 90 degrees separated from the brake lever. (Note: If you have wider
aftermarket bars and the lever perch will be installed directly over the handlebars instead of the grips, you can
use the nylon spacer provided in your kit.)
3) Thread allen screws back into perch housing, being careful not to cross-thread screws.
4) Once the lever perch fits snugly and the allen screws thread smoothly, tighten the screws to prevent the perch
from rotating loosely on the handlebar. CAUTION: In no case should your GOLDFINGER throttle lever be
parallel or close to your brake lever!
B) Installation of Right-Side Throttle Adapter Plate (See Photo B)
A
IF YOUR SLED IS AN 07’ XRS, X, X-SUMMIT OR 08ʼ 600, 800, 1000 MODEL THEN PLEASE
REFER TO THE INCLUDED ZIPLOC BAG WITH THE ORANGE LABEL FOR COMPLETION OF STEP B.
(For your convenience, the right-side cable attachment (hereinafter called “barrel bolt”) has been pre-assembled on the adapter plate and does NOT
need to be removed for installation.)
1) Using 3mm allen wrench, remove the bottom-mounted OEM throttle pivot allen shoulder screw from the throttle block housing.
2) Carefully place one flat washer (found in Ziploc bag) between the throttle block housing and the throttle flipper (see arrow in photo B). Apply a small
dab of blue loctite to the OEM allen shoulder screw threads, then insert first up through the large center hole of the stainless steel adapter plate
(with the bent tab end toward you), then up through the throttle flipper, then through a stainless steel flat washer, and finally thread it up into the
throttle block housing.