Norgren F-Series Plus Cylinders - Manual

Our policy is one of continued research and development. We therefore reserve the right to amend,
without notice, the specifications given in this document.
11/09 N/US - 5.4.251.01
F-Series Plus Cylinders
Single and Double acting
9/16" to 4" bore
Technical Data:
Medium:
Filtered, lubricated or non-
lubricated, compressed air
Operating Pressure
200 psig (13.6 Bar) Max.
Temperature Range:
Standard Nitrile seals:
-40°F to 200°F (-40°C to 93°C)
150°F max. with Bumper
Option
High Temp seals:
-20°F to 400°F (-29°C to
205°C)
*With dew point of supply air less than air
temperature below 35°F (2°C).
Lubrication:
All F-Series Plus cylinders are
prelubricated at the time of
assembly with a Teflon®-Based
grease, for non-lube service and
long life.
Side Loading:
Cylinders are specifically designed
to push and pull. Side loading and
misalignment of the piston rod
should be avoided to ensure
maximum operating performance
and life.
Materials:
Cylinder Body:
304 Stainless Steel
Head and Cap:
Clear Anodized Aluminum Alloy
Piston Rod:
303 Stainless Steel
Rod Bearing:
Oil Impregnated Bronze
Piston:
Aluminum Alloy
Rod & Piston seals:
Buna-N
Options selector
FP 106 x 2.375 - PTM - PS
Series Substitute
Single Rod end FP
Double Rod end FPD
Spring Extend FPC
Spring Retract FPR
Bore Substitute
9/16" 056
3/4" 075
1-1/16" 106
1-1/2" 150
2" 200
2-1/2" 250
3" 300
4" 400
Stroke
Increments of 1/8"
Mounting Options Substitute
*Screw Clearance Holes Front SCF
*Screw Clearance Holes Rear SCR
*Screw Clearance Holes Both ends SCB
Basic Model (std. c'bored mtg. holes) BAM
**Front Trunnion TMF
**Rear Trunnion TMR
**Trunnion both ends TMB
Pivot Mount PTM
Threaded mounting holes Front THF
Threaded mounting holes Rear THC
Threaded mounting holes Both ends THB
***Nose Mount NMT
Options Substitute
Bumper both ends (not avail. with HT) 1 UB
Bumper Head (not avail. with HT) 1 UH
Bumper Cap (not avail. with HT) 1 UC
Non-Standard Female Thread* FT(__)
Heavy Duty Rear End Cap² HD
Alternate Port Location PL(__)
Low Friction Seals² LF
Magnetic Piston² PS
Switch Rail and Position
(switches ordered separately) M1,M2, M3,M4
No Rod Thread
PR
Non-Standard Male Thread TM(__)
Thread Extension over standard TX(__)
(specify additional length) 3
Rod Extension over standard RX(__)
(specify additional length) 3
Stainless Steel Fasteners SF
(125 PSI Max)
High Temperature Seals 4 **HT
Rod Wiper RW
Hollow Rod 5 RH
1 Stroke is reduced by .03" per bumper.
Bumpers are rated to 150°F
2 Overall length of cylinder may increase with
this option.
3 Consult factory for negative thread or rod
extensions.
4 Not available in single or reverse acting
models.
5 Double rod end models only
* Not available in 9/16" bore.
* Screw clearance to allow bolt head to pass through - no
counter bores
** Not available on 9/16" bore
*** Available in FP, FPC, and FPR. Includes a heavy duty end
cap and rod wiper.