Norgren Roundline Plus Stainless Steel Body Actuators - Manual

ACT- 134
A
C
TUA
TORS
Norgren.com/usa – 303.794.2611 – [email protected]
Full range of bore sizes
All essential models
Optional Ecology seal
Technical data
Medium:
Filtered, lubricated or non-
lubricated, compressed air
Maximum Operating
Pressure:
250 psig (17.2 bar)
Temperature Range*:
Standard Nitrile Seals:
-20° to 200°F (-29° to 93°C)
Viton/High temp Seals:
-20° to 400°F (-29° to 205°C)
*With dew point of supply air less than air
temperature below 35°F (2°C)
Lubrication:
All Roundline Plus cylinders are
pre-lubricated during assembly
with a Teflon ® based grease for
non-lube service and long life.
Materials
Cylinder Body:
304 Stainless Steel
Head and Cap:
Aluminum Alloy
Piston Rod:
Stainless steel in double rod
cylinders, and 5/16", 7/16", and
9/16" bores. Chrome plated
steel in all other bore sizes
Rod Bearing: Oil Impregnated
Sintered Bronze
Piston: Aluminum Alloy or
stainless steel
Rod & Piston Seals: Nitrile
Pivot Bracket, Rod Clevis, Foot
Bracket, Mounting Nut: Bright Zinc
Plated Carbon Steel
Options selector
RP 075 x 2.50 - DAN - PS
Bore Size
5/16"
031
7/16" 043
9/16" 056
3/4" (E) 075
7/8" 087
1-1/16" (E) 106
1-1/4" (E) 125
1-1/2" (E) 150
1-3/4" 175
2" (E) 200
2-1/2" (E) 250
3" (E) 300
E - Available with Ecology Seals
Series
Roundline Plus
RP
Roundline Plus with
Ecology seals*
*ERP
Stroke
Increments of 1/16" up to
a maximum. See table
Mounting Options
Single Acting Nose
SAN
Single Acting Pivot SAP
Single Acting Front Block SBF
Single Acting Rear Block SBR
Single Acting Front Trunnion STF
Single Acting Rear Trunnion STR
Single Acting Non-Rotating Nose NRN
Single Acting Non-Rotating Pivot NRP
Reverse Acting Nose RAN
Reverse Acting Pivot RAP
Reverse Acting Front Block RAF
(available in 3/4", 1-1/16" & 1-1/2” only)
Reverse Acting Rear Block
RAR
Double Acting Nose DAN
Double Acting Pivot DAP
Double Acting Double End Mount DAD
Double Acting Front Block DAF
Double Acting Rear Block DAR
Double Acting Front Trunnion DFT
Double Acting Rear Trunnion DRT
Double Acting Double Rod End DRD
Mounting Options
Adjustable Cushion Head End
CH †††
Adjustable Cushion Cap End CC †††
Adjustable Cushion Both Ends CB †††
Bumpers UB
Alternate Port Location PL(__)
Side Ported End Cap (DAN, SAN, and PC
DAFmodels only, note length adder)
Magnetic Piston
PS
Switch Rail and location M1,M2,
M3,M4
Non-Adjustable cushion head end NH*
Non-Adjustable cushion cap end NC*
Non-Adjustable cushions both ends NB*
No Flats (no plain rod stick out) NF**
No Rod Thread PR
No Pin NP
Pivot Bushing (no pin) PO
Non-Standard Male Thread TM(__)
Non-Standard Female Thread FT(__)
Thread extension over standard TX†(__)
(specify additional length)
Rod extension over standard
RX†(__)
(specify additional length)
Stainless Steel piston rod
SS
(standard on certain models)
Viton/High Temperature Seals
HT
Rod Wiper (not available with HT) RW
Maximum Stroke Lengths††
Bore
Single &
Reverse Acting
Double
Acting
5/16" 4 12
7/16"-9/16" 12 36
3/4"-1-3/4" 12 36
2" 4 36
2-1/2"-3" - 36
* ERP, ecology cylinders come complete with non-
adjustable cushions both ends (NH, NC, NB, options not
required in model number of ERP cylinder). ERP on DAP,
DAF, DAD, and DAN models only (add PC option length
adder to DAN models)
** Available only on 1-1/16" bore - RAN and RAP, mounts.
† Male thread extension only. Consult factory for negative
thread or rod extensions.
††† Available on 075, 106, 150, 200, 250 & 300 Bores.
†† Consult factory for longer stroke lengths.
Roundline Plus
Stainless Steel Body Actuators
5/16" to 3" bore
Single and Double acting actuators